manualshive.com logo in svg

Canon imageRUNNER ADVANCE C2225, Basic Operation Gude

Share
Download
Canon imageRUNNER ADVANCE C2225 Basic Operation Gude Download Page 144

144

When an Error Code Is Displayed

If a job or operation does not complete successfully, the error code is displayed on the Details screen for Log on the Status 

Monitor/Cancel screen.

You can check the error code in the following locations: 

■

●

Details■screen■for■Log■on■the■Status■Monitor/Cancel■screen:

When a job or operation is not completed normally:

■

●

Results■row■of■the■Communication■Management■Report:

If an error occurs during a send, receive, or fax job, the error code is printed.

iRADV C2230

04/08/2012

START TIME END TIME

TYPE

DELIVER

DEPT.ID

ADDRESS BOOK

DEPT.ID

ADDRESS BOOK

DEPT.ID

ADDRESS BOOK

DEPT.ID

ADDRESS BOOK

DELIVER

DELIVER

DELIVER

TO/FROM

DATA DETAILS

RESULT

DEVICE INFORMATION COMMUNICATION LOG REPORT

For information on error codes and instructions on resolving errors, see e-Manual > Problem Solving.

Summary of Contents for imageRUNNER ADVANCE C2225





















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands