Brother HL-5580D Service Manual Download Page 67

Page: 67 / 433

2-41

Confidential

Supplies

Drum End Soon.

The number of rotations of the
drum unit is reaching the upper
limit.

4000

2-49

Replace Drum

The number of rotations of the
drum unit has reached the upper
limit. (Printing does not stop.)

4200

2-49

Toner Low

Dot counter or develop roller
counter of the toner is reaching
the upper limit.

4B01

2-50

Too many bins

MX(2 or 4) bin sensor detected
that the only one of the two
removable plates is removed from
the MX.

7F00

2-70

Too Many Trays

Turn the power off and
remove additional
trays.

Detected more LTs than
connectible limit.

6D00

2-55

Unable to
Update:01

Check the firmware
update file and try
again.

An error occurred during the
automatic firmware update with
USB flash memory.

---

4.11.2

Unable to
Update:02

Unable to
Update:03

Unable to
Update:04

Unable to
Update:05

Unable to
Update:06

Unable to
Update:07

Unable to
Update:08

Unusable Device Unusable device.

The connected USB device is not
supported.

---

4.11.3

2-sided Disabled -

The back cover/duplex tray sensor
detected that the cover was open
when duplex printing is started.
(Before registering printing data to
engine)

8903

2-75

The back cover/duplex tray sensor
detected that the cover was open
during duplex printing. (After
registering printing data to engine)

8904

2-75

Error message

Description

Error

codes

Refer

to:

First line

Second line

Summary of Contents for HL-5580D


















































































































































































































































































































































































































































Search results

Summary of Contents for HL-5580D

Reviews:

Brands by name

Popular brands

Brother HL-5580D, Service Manual

Search results

Summary of Contents for HL-5580D

Reviews:

Brands by name

Popular brands