manualshive.com logo in svg

Brother HL-5580D, Service Manual

Share
Download
Brother HL-5580D Service Manual Download Page 91

2-65

Confidential

Error code 7702

When printing from the paper tray 5, the registration front sensor or the T2/T3/T4/T5TT jam 
sensor does not detect paper pass within the specified time after the T5TT paper feed sensor 
detected paper pass.

<User Check>

• Remove the jammed paper.
• Add the paper properly using the paper tray 5 paper guide.
• Install the latest main firmware.

Step

Cause

Remedy

1

Foreign object in the front of the 
machine

Remove the foreign object.

2

Registration front actuator 
attachment failure

Reattach the registration front actuator.

3

T2/T3/T4/T5TT jam sensor 
attachment failure

Reattach the T2/T3/T4/T5TT jam sensor.

4

Connection failure of the 
registration front/rear sensor 
harness

Reconnect the registration front/rear sensor 
harness.

5

Connection failure of the T2/T3/
T4/T5TT jam sensor harness

Reconnect the T2/T3/T4/T5TT jam sensor 
harness.

6

Connection failure of the TT 
control PCB harness

Reconnect the TT control PCB harness.

7

Connection failure of the T3/T4/
T5TT release clutch harness

Reconnect the T3/T4/T5TT release clutch 
harness.

8

T3/T4/T5TT release clutch 
failure

Replace the T3/T4/T5TT release clutch.

9

Registration front/rear sensor 
PCB failure

Replace the registration front/rear sensor PCB 
ASSY.

10

T2/T3/T4/T5TT jam sensor PCB 
failure

Replace the T2/T3/T4/T5TT jam sensor PCB 
ASSY.

11

TT control PCB failure

Replace the TT control PCB ASSY.

12

High-voltage power supply PCB 
failure

Replace the high-voltage power supply PCB 
ASSY.

13

Damaged gears in the TT paper 
feeding system

Replace the TT.

14

Main PCB failure

Replace the main PCB ASSY.

Summary of Contents for HL-5580D


















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands