manualshive.com logo in svg

Brother HL-5580D, Service Manual

Share
Download
Brother HL-5580D Service Manual Download Page 192

3-47

Confidential

(4) Close the front cover ASSY. Remove the two bosses on the MP cover ASSY, and 

remove the MP cover ASSY from the front cover ASSY.

(5) Remove the MP damper spring from the MP cover ASSY.

Fig. 3-28

Fig. 3-29

Note:

• Remove the MP cover ASSY while pushing "A" on the front cover ASSY in the 

direction of the arrow.

Assembling Note:

• Attach the MP damper spring as described in the figure below.

MP damper spring

Front cover ASSY

MP cover ASSY

Boss

"A"

Boss

MP damper spring

MP cover ASSY

Front cover ASSY

Summary of Contents for HL-5580D


















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands