Brother HL-5580D Service Manual Download Page 111 | Manualshive

Page: 111 / 433

background image

2-85

Confidential

4.2.2 No paper is fed from LT

<User Check>

• Check that the paper is set in the paper tray correctly.
• Check that there is not too much paper set in the paper tray.
• Flip over the paper in the paper tray or rotate the paper 180°.
• Check that the thickness of the paper is 60 to 120 g/m

2

(paper tray 2 to 4).

• Check that the MP tray, T1 or TT is not set as the paper tray.
• Flip through the paper and reset it in the paper tray.
• Clean the paper pick up roller.
• Install the latest main firmware.

Step

Cause

Remedy

1

Dirt on a paper dust cleaning

roller of the paper tray

Clean the appropriate paper dust cleaning

roller. (Refer to

2

Attachment failure of a roller

holder ASSY

Reattach the appropriate roller holder ASSY

correctly.

3

Connection failure of the paper

feed motor harness

Reconnect the paper feed motor harness.

4

Connection failure of an LT

paper feed sensor harness

Reconnect the appropriate LT paper feed

sensor harness.

5

Connection failure of an LT

control PCB flat cable

Reconnect the appropriate LT control PCB flat

cable.

6

Connection failure of an LT

release clutch harness

Reconnect the appropriate LT release clutch

harness.

7

Connection failure of an LT

pickup clutch harness

Reconnect the appropriate LT pickup clutch

harness.

8

An LT paper empty actuator
coming off

Reattach the appropriate LT paper empty
actuator.

9

Abrasion of a paper pick up

roller

Replace the appropriate PF kit.

10

An LT release clutch failure

Replace the appropriate LT release clutch.

11

An LT pickup clutch failure

Replace the appropriate LT pickup clutch.

12

An LT paper empty sensor

failure

Replace the appropriate LT paper empty

sensor PCB ASSY.

13

Damaged a plate gear

Replace the appropriate plate gear.

14

Damaged fuser gear

Replace the fuser gear.

15

Damaged an LT/TT connector

Replace the appropriate LT/TT connector.

16

Paper feed motor failure

Replace the paper feed motor.

17

An LT control PCB failure

Replace the appropriate LT control PCB ASSY.

18

Panel PCB failure

Replace the panel PCB ASSY.

19

Damaged LT drive gear system

of the machine

Replace the main frame L ASSY.

20

Damaged fuser unit

Replace the fuser unit.

21

Main PCB failure

Replace the main PCB ASSY.

«
...
109
110
111
112
113
...
»

Summary of Contents for HL-5580D


















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for HL-5580D

Brand: CAB Pages: 263

iPF650 - imagePROGRAF Color Inkjet Printer

Brand: Canon Pages: 40

iP90 - PIXMA Color Inkjet Printer

Brand: Canon Pages: 2

iPF650 - imagePROGRAF Color Inkjet Printer

Brand: Canon Pages: 16

iP100 - PIXMA Color Inkjet Printer

Brand: Canon Pages: 2

imageRUNNER ADVANCE C5560

Brand: Canon Pages: 67

imageRUNNER 3300

Brand: Canon Pages: 366

IMAGERUNNER ADVANCE C5051

Brand: Canon Pages: 252

iPF710 - imagePROGRAF Color Inkjet Printer

Brand: Canon Pages: 2

Brand: Canon Pages: 58

image Prograf iPF680 Series

Brand: Canon Pages: 132

Brand: Canon Pages: 44

imageClass LBP6230dw

Brand: Canon Pages: 16

Brand: Canon Pages: 2

imageprograf IPF785

Brand: Canon Pages: 42

Brand: Canon Pages: 148

Color Bubble Jet BJC-8200

Brand: Canon Pages: 6

Color Bubble Jet BJC-1000 Series

Brand: Canon Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands