manualshive.com logo in svg

Brother HL-5580D, Service Manual

The Brother HL-5580D Service Manual is an essential resource for troubleshooting and maintaining your printer. Our website offers a comprehensive manual for download, completely free of charge. Ensure optimal performance and extend the lifespan of your printer with this indispensable manual. Download it now from manualshive.com.

Share
Download
background image

2-6

Confidential

2.3 Operation of Each Part

Part name

Operation

Paper pick up roller

Feeds paper from the paper tray to the separation roller.

Separation roller, 
Separation pad

Separates paper fed from the paper tray into single sheets.

Paper feed actuator 
(Paper feed sensor)

Detects paper trays (open / closed).
Detects paper jams in paper trays.
Determines whether paper is fed from the paper tray.

Paper empty actuator 
(Paper empty sensor)

Detects paper in the paper tray.
(Models with 520-sheet LT/TT and HL-5580D/5585D only.)

TT jam actuator 
(TT jam sensor)

Detects paper jams in the front section of the tray. (TT only)

TT balance sensor L/R

Detects if the TT is mounted properly. (TT only)

Registration front actuator 
(Registration front sensor)

Detects the front edge of the paper to control the registration 
roller drive.
Detects paper jams in the front section of the machine.
Determines whether paper is fed from the paper tray.

Registration roller

Corrects the paper alignment when the paper makes contact 
with the stopped registration roller. After the correction, it rotates 
to feed the paper to the feeding path.

Registration rear actuator 
(Registration rear sensor)

Detects paper pass and adjusts the writing start position for the 
paper.
Detects paper jams in the front or center section of the machine.
Detects the rear edge of the paper to determine the paper size.

Heat film, 
Pressure roller

Fuses the toner transferred to paper by heat and pressure, and 
feeds paper to the eject roller 1.

Eject actuator 
(Eject sensor)

Determines whether paper is ejected from the fuser unit.
Detects the rear edge of the paper in duplex printing mode to 
adjust the turn-over timing of the eject roller 2. Detects paper 
jam in the rear section of the machine.
Calculates time to open/close the MX flapper 1, 2 and 3 after the 
paper has been fed when ejecting the paper to MX bin.

Eject roller 1

Feeds the paper ejected from the fuser unit to eject roller 2.

Eject roller 2

Ejects the paper to the output tray of the machine.
During the duplex printing, the eject roller 2 rotates conversely 
and feeds the paper to the duplex tray after the paper has been 
fed from the eject roller 2 with the first side printed.

Duplex paper feed roller

Feeds the paper passing through the duplex tray to the 
registration roller.

Front cover sensor

Detects open front cover.

Back cover/duplex tray 
sensor

Detects open / closed back cover or the duplex tray is set.

MP paper pick up roller

Feeds paper from the MP tray to the MP separation roller.

Summary of Contents for HL-5580D


















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for HL-5580D

Xerox 3270 Programmer'S Manual preview
3270
Brand: Xerox Pages: 34
NEC NEFAX - 691 B/W Laser Introduction Manual preview
NEFAX - 691 B/W Laser
Brand: NEC Pages: 20
Datamax M-Class Mark II Maintenance Manual preview
M-Class Mark II
Brand: Datamax Pages: 94
Quest Payment Systems Donation Point Even Quick Start Manual preview
Donation Point Even
Brand: Quest Payment Systems Pages: 2
Ricoh Aficio SP C730DN User Manual preview
Aficio SP C730DN
Brand: Ricoh Pages: 100
Partex Moca Quick Start Manual preview
Moca
Brand: Partex Pages: 12
Oki B2540 Brochure & Specs preview
B2540
Brand: Oki Pages: 2
Xerox WorkCentre 3615DN Brochure & Specs preview
WorkCentre 3615DN
Brand: Xerox Pages: 4
Oce LightJet 430 Site Preparation Manual preview
LightJet 430
Brand: Oce Pages: 32
Intellisystem ThermalTronix TT-1025EX-MIL User Manual preview
ThermalTronix TT-1025EX-MIL
Brand: Intellisystem Pages: 11
Xprinter XP-470 Series User Manual preview
XP-470 Series
Brand: Xprinter Pages: 40
iDPRT SP410 User Manual preview
SP410
Brand: iDPRT Pages: 41
Xerox Nuvera 100 roduction Systems Paper Manual preview
Nuvera 100 roduction Systems
Brand: Xerox Pages: 70
Output Technology LaserMatrix LM2405 Operator'S Manual preview
LaserMatrix LM2405
Brand: Output Technology Pages: 249
Lexmark Color Jetprinter 1020 Service Manual preview
Color Jetprinter 1020
Brand: Lexmark Pages: 4
Canon imageRUNNER ADVANCE DX C5870i Faq Manual preview
imageRUNNER ADVANCE DX C5870i
Brand: Canon Pages: 100
Canon imageRUNNER ADVANCE C356iF Faq Manual preview
imageRUNNER ADVANCE C356iF
Brand: Canon Pages: 96
Canon imageRUNNER ADVANCE C350 series Service Manual preview
imageRUNNER ADVANCE C350 series
Brand: Canon Pages: 1173

Brands by name

Popular brands

Load more brands