Brother HL-5580D Service Manual Download Page 105

Page: 105 / 433

2-79

Confidential



Error code 9309

Detected that there was no paper set in all trays when TrayAuto was selected for printing.



Error code 9400

Firmware version of the main PCB is older than that of the TT, MX and LT.

• Set paper in the paper tray.

Step

Cause

Remedy

Malfunction of an LT control
PCB or TT control PCB

Install the latest main firmware.

Connection failure of an LT/TT
paper empty sensor harness

Reconnect the appropriate LT/TT paper empty
sensor harness.

Connection failure of the T1
paper feed sensor harness

Reconnect the T1 paper feed sensor harness.
(Models with 250-sheet only)

An LT/TT paper empty actuator
caught in some sections of the
machine

Reattach the appropriate LT/TT paper empty
actuator.

T1 paper feed actuator caught in
some sections of the machine

Reattach the T1 paper feed actuator. (Models
with 250-sheet only)

Abrasion of a PF kit

Replace the appropriate PF kit.

An LT/TT paper empty sensor
PCB failure

Replace the appropriate LT/TT paper empty
sensor PCB ASSY.

T1 paper feed sensor PCB
failure

Replace the T1 paper feed sensor PCB ASSY.
(Models with 250-sheet only)

T1, T2, or T3(LT or TT) pickup
clutch failure

Replace the T1, T2, or T3(LT or TT) pickup
clutch.

Paper feed motor failure

Replace the paper feed motor. (Models with
250-sheet only)

High-voltage power supply PCB
failure

Replace the high-voltage power supply PCB
ASSY.

An LT control PCB failure

Replace the appropriate LT control PCB ASSY.

TT relay PCB failure

Replace a TT relay PCB ASSY.

TT control PCB failure

Replace the TT control PCB ASSY.

Damaged gears in the paper
feeding system

Replace the main frame L ASSY. (Models with
250-sheet only)

Main PCB failure

Replace the main PCB ASSY.

• Install the latest main firmware.

Step

Cause

Remedy

Main firmware version and
firmware version of the TT, MX
and LT do not match

Install the latest main firmware.

Summary of Contents for HL-5580D


















































































































































































































































































































































































































































Search results

Summary of Contents for HL-5580D

Reviews:

Brands by name

Popular brands

Brother HL-5580D, Service Manual

Search results

Summary of Contents for HL-5580D

Reviews:

Brands by name

Popular brands