manualshive.com logo in svg

Brother HL-5580D, Service Manual

Share
Download
Brother HL-5580D Service Manual Download Page 209

3-64

Confidential

(2) Disconnect all harnesses and flat cables from the main PCB ASSY.

Fig. 3-51

Note:

• After disconnecting flat cables, check that each cable is not damaged at its end or 

shortcircuited.

• When connecting flat cables, do not insert them at an angle. After insertion, check 

that the cable is not at an angle.

Eject motor harness

Relay front harness

Toner amount detection sensor PCB harness (light emission)

Internal temperature sensor harness

Paper empty sensor harness 

*3

Laser unit flat cable

Low-voltage power supply harness

Paper feed motor harness

HVPS flat cable

LT/TT connector harness

External temperature/humidity 
sensor harness

Back cover/duplex 
tray sensor harness

MX connector harness 

*1

Erase lamp harness 

*2

Eject sensor harness

*1

 Touch panel models only

*2

 Models with 520-sheet T1 only

*3

 Models with 520-sheet T1 and 

HL-5580D/5585D only

Panel flat cable 

*1

Summary of Contents for HL-5580D


















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands