Brother HL-5580D Service Manual Download Page 306

Page: 306 / 433

3-161

Confidential

12.7 Fan motor

(1) Release the fan motor harness from the securing fixtures, and disconnect it from the fan

motor relay harness.

(2) Release all hooks to remove the fan motor from the air duct.

Fig. 3-157

Harness routing: Refer to

“14. Upper right of the TT”

Assembling Note:

• Place the fan motor so that the attached label faces outwards.

• Do not pull the fan motor relay harness too much, it may cause a connection failure

with the TT control PCB ASSY.

• When wiring, make sure that the fan motor harness does not come out of the air

duct.

Hooks

Hole

Label

Fan motor

Hook

Fan motor harness

Air duct

Fan motor relay harness

Summary of Contents for HL-5580D


















































































































































































































































































































































































































































Search results

Summary of Contents for HL-5580D

Reviews:

Brands by name

Popular brands

Brother HL-5580D, Service Manual

Search results

Summary of Contents for HL-5580D

Reviews:

Brands by name

Popular brands