Brother HL-5580D Service Manual Download Page 96

Page: 96 / 433

2-70

Confidential



Error code 7B05

The MX 4bin stack sensor does not detect paper pass within the specified time after the MX
jam upper sensor detected paper pass.



Error code 7F00

MX(2 or 4) bin sensor detected that the only one of the two removable plates is removed
from the MX.

• Remove the jammed paper.
• Close the MX back cover correctly.

Step

Cause

Remedy

Foreign object in the rear of the
machine

Remove the foreign object.

MX flapper 3 attachment failure Reattach the MX flapper 3.

MX 4bin stack actuator
attachment failure

Reattach the MX 4bin stack actuator.

Connection failure of the MX
4bin stack sensor harness

Reconnect the MX 4bin stack sensor harness.

Connection failure of the MX
relay PCB harness

Reconnect the MX relay PCB harness.

MX 4bin stack sensor failure

Replace the MX 4bin stack sensor.

MX relay PCB failure

Replace the MX relay PCB ASSY.

MX control PCB failure

Replace the MX control PCB ASSY.

Main PCB failure

Replace the main PCB ASSY.

• Remove or attach both of the two removable plates.
• Reattach the removable plates.

Step

Cause

Remedy

Connection failure of the MX
2bin detection sensor harness
or MX 4bin detection sensor
harness

Reconnect the MX 2bin detection sensor
harness or MX 4bin detection sensor harness.

MX 2bin detection sensor or MX
4bin detection sensor failure

Replace the MX 2bin detection sensor or MX
4bin detection sensor.

MX control PCB failure

Replace the MX control PCB ASSY.

Main PCB failure

Replace the main PCB ASSY.

Summary of Contents for HL-5580D


















































































































































































































































































































































































































































Search results

Summary of Contents for HL-5580D

Reviews:

Related manuals for HL-5580D

Brands by name

Popular brands

Brother HL-5580D, Service Manual

Search results

Summary of Contents for HL-5580D

Reviews:

Related manuals for HL-5580D

Brands by name

Popular brands