manualshive.com logo in svg

Brother HL-5580D, Service Manual

The Brother HL-5580D Service Manual is an essential resource for troubleshooting and maintaining your printer. Our website offers a comprehensive manual for download, completely free of charge. Ensure optimal performance and extend the lifespan of your printer with this indispensable manual. Download it now from manualshive.com.

Share
Download
background image

2-56

Confidential

Error code 7100

The eject sensor remains ON (paper pass detected) even after the registration rear sensor 
detected the end of paper pass.

Error code 7200

When feeding from the MP tray, the registration rear sensor does not detect paper pass 
within the specified time after the registration front sensor detected paper pass.

<User Check>

• Remove the jammed paper.
• Check if the back cover is open during duplex printing.

Step

Cause

Remedy

1

Foreign object in the rear of the 
machine

Remove the foreign object.

2

Eject actuator caught in some 
sections of the machine

Reattach the eject actuator.

3

Fuser cover attachment failure

Reattach the fuser cover.

4

Eject sensor failure

Replace the eject sensor PCB ASSY.

5

High-voltage power supply PCB 
failure

Replace the high-voltage power supply PCB 
ASSY.

6

Fuser cover failure

Replace the fuser cover.

7

Damaged eject roller 1 drive 
gears

Replace the main frame L ASSY.

8

Main PCB failure

Replace the main PCB ASSY.

<User Check>

• Remove the jammed paper.
• Add the paper properly using the MP tray paper guide.
• Close the front cover correctly.

Step

Cause

Remedy

1

Foreign object in the front of the 
machine

Remove the foreign object.

2

Registration rear actuator 
coming off or caught in some 
sections of the machine

Reattach the registration rear actuator.

3

Connection failure of the 
registration front/rear sensor 
harness

Reconnect the registration front/rear sensor 
harness.

4

Connection failure of the 
registration clutch harness

Reconnect the registration clutch harness.

5

MP feed frame attachment 
failure

Reattach the MP feed frame.

6

Registration rear sensor failure Replace the registration front/rear sensor PCB 

ASSY.

7

Registration clutch failure

Replace the registration clutch.

8

High-voltage power supply PCB 
failure

Replace the high-voltage power supply PCB 
ASSY.

9

Damaged gears in the paper 
feeding system

Replace the main frame L ASSY.

10

Main PCB failure

Replace the main PCB ASSY.

Summary of Contents for HL-5580D


















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for HL-5580D

Ricoh Type 8000 Printer Reference preview
Type 8000
Brand: Ricoh Pages: 152
Xerox VersaLink C400V User Manual preview
VersaLink C400V
Brand: Xerox Pages: 196
Xerox WorkCentre 6400XF Evaluator Manual preview
WorkCentre 6400XF
Brand: Xerox Pages: 24
Mitsubishi CP-9500DW Features And Specifications preview
CP-9500DW
Brand: Mitsubishi Pages: 2
AstroJet IB-9000-6P Operator'S Manual preview
IB-9000-6P
Brand: AstroJet Pages: 32
GCC Technologies LaserPro StellarMark IFII Series User Manual preview
LaserPro StellarMark IFII Series
Brand: GCC Technologies Pages: 111
Kimo KDIP-2 User Manual preview
KDIP-2
Brand: Kimo Pages: 2
Star Micronics SP200 Series User Manual preview
SP200 Series
Brand: Star Micronics Pages: 127
Canon imageCLASS LBP247dw Setup Manual preview
imageCLASS LBP247dw
Brand: Canon Pages: 32
Epson Expression Photo XP-750 Basic Manual preview
Expression Photo XP-750
Brand: Epson Pages: 187
Epson Expression Photo XP-950 Manual preview
Expression Photo XP-950
Brand: Epson Pages: 300
Epson Expression Photo XP-960 User Manual preview
Expression Photo XP-960
Brand: Epson Pages: 325
Xerox PHASER 6121MFP Quick Use Manual preview
PHASER 6121MFP
Brand: Xerox Pages: 16
Epson Expression Photo XP-950 Specifications preview
Expression Photo XP-950
Brand: Epson Pages: 4
Epson L200 Service Manual preview
L200
Brand: Epson Pages: 47
Epson Expression Premium XP-820 Product Specifications preview
Expression Premium XP-820
Brand: Epson Pages: 4
Epson Expression Premium XP-800 Product Overview And Specifications preview
Expression Premium XP-800
Brand: Epson Pages: 2
Epson L130 Start Here preview
L130
Brand: Epson Pages: 4

Brands by name

Popular brands

Load more brands