Brother HL-5580D Service Manual Download Page 80

Page: 80 / 433

2-54

Confidential



Error code 6901

An error occurred in the fuser unit when the power switch was turned ON or sleep mode was
released.

Error code 6902

Rechecking the error after the power switch was turned OFF and then ON again because an
error was detected in the fuser unit.

(This message is displayed for approximately 15 minutes when the machine is restarted after
error code 6901 has occurred.)



Error code 6A00

Detected discharge that may be attributable to dirty corona wire on the drum unit.

Step

Cause

Remedy

Connection failure of a fuser unit
harness

Reconnect the fuser unit harness.

Connection failure of the eject
sensor harness

Reconnect the eject sensor harness.

Eject sensor PCB failure

Replace the eject sensor PCB ASSY.

Fuser unit failure

Replace the fuser unit.

Low-voltage power supply PCB
failure

Replace the low-voltage power supply PCB
ASSY.

Main PCB failure

Replace the main PCB ASSY.

Note:

• Turn OFF the power switch. After the fuser unit has cooled sufficiently, turn ON the

power switch again and leave the machine for 15 minutes. This problem may then be
cleared.

• To release the fuser unit error after taking appropriate measures, enter the

maintenance mode once and quit it with the maintenance code 99.

• Slide the green tab of the drum unit to left and right for two to three times to clean the

corona wire.

• Clean the electrode of the drum unit.
• Replace the drum unit.

Step

Cause

Remedy

Dirt on the high-voltage power
supply PCB terminal

Clean the electrodes of the machine.
(Refer to

Fig. 2-7

High-voltage power supply PCB
attachment failure

Check if each electrode comes back smoothly
after pressing it. If not, reattach each electrode.

High-voltage power supply PCB
failure

Replace the high-voltage power supply PCB
ASSY.

Main PCB failure

Replace the main PCB ASSY.

Summary of Contents for HL-5580D


















































































































































































































































































































































































































































Search results

Summary of Contents for HL-5580D

Reviews:

Related manuals for HL-5580D

Brands by name

Popular brands

Brother HL-5580D, Service Manual

Search results

Summary of Contents for HL-5580D

Reviews:

Related manuals for HL-5580D

Brands by name

Popular brands