Home
/
Brother
/
HL-5580D
/
Service Manual

Brother HL-5580D, Service Manual

Share

Page: 144 / 433

Brother HL-5580D Service Manual Download Page 144

2-118

Confidential

4.11 Troubleshooting for Other Problems

4.11.1 Cannot print

4.11.2 Cannot update firmware

4.11.3 USB direct interface errors

<User Check>

- Turn the power switch OFF and then ON again.
- Check that the USB cable is connected to the host correctly.
- Check that the LAN cable is connected to the host correctly.
- Replace the USB cable.
- Replace the LAN cable.
- Check that the maximum printable page number has not been exceeded.
- Check that the PC Print is not forbidden.
- Check the print limit ID.
- Check the network connection.
- Check the relevant section in the Network Setting Guide.
- Check that the print data is not damaged.
- Install the latest main firmware.
- Match the document size with the one specified in the driver.

Step

Cause

Remedy

1

Connection failure of the wireless
LAN connector

Reconnect the wireless LAN connector.

2

Wireless LAN PCB failure

Replace the wireless LAN PCB.

3

Main PCB failure

Replace the main PCB ASSY.

<User Check>

- Make sure that there is no other function running.
- Turn the power switch OFF and then ON again.

Step

Cause

Remedy

1

Firmware version does not match

Reinstall the latest sub firmware and main
firmware in this order.

2

Main PCB failure

Replace the main PCB ASSY.

<User Check>

- Replace the USB flash memory.
- Check that the extension of data in the USB flash memory is correct.

Step

Cause

Remedy

1

USB host circuit failure

Replace the main PCB ASSY.

«
...
142
143
144
145
146
...
»

Summary of Contents for HL-5580D


















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands