manualshive.com logo in svg

Brother HL-5580D, Service Manual

Share
Download
Brother HL-5580D Service Manual Download Page 101

2-75

Confidential

Error code 8903

The back cover/duplex tray sensor detected that the cover was open when duplex printing is 
started. (Before registering printing data to engine)

Error code 8904

The back cover/duplex tray sensor detected that the cover was open during duplex printing. 
(After registering printing data to engine)

Error code 8A01

The registration rear sensor detected that the paper fed was smaller or larger than the 
specified size in duplex printing mode.

<User Check>

• Close the back cover correctly.
• Attach the duplex tray correctly.

Step

Cause

Remedy

1

Back cover/duplex tray sensor 
attachment failure

Reattach the back cover/duplex tray sensor.

2

Connection failure of the back 
cover/duplex tray sensor 
harness

Reconnect the back cover/duplex tray sensor 
harness.

3

Damaged back cover

Replace the back cover.

4

Damaged duplex tray

Replace the duplex tray.

5

Main PCB failure

Replace the main PCB ASSY.

<User Check>

• Use specified paper.

Step

Cause

Remedy

1

Registration rear actuator 
caught in some sections of the 
machine

Reattach the registration rear actuator.

2

Registration rear sensor failure Replace the registration front/rear sensor PCB 

ASSY.

3

High-voltage power supply PCB 
failure

Replace the high-voltage power supply PCB 
ASSY.

4

Main PCB failure

Replace the main PCB ASSY.

Summary of Contents for HL-5580D


















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands