manualshive.com logo in svg

Brother HL-5580D, Service Manual

Share
Download
Brother HL-5580D Service Manual Download Page 76

2-50

Confidential

Error code 4600

The number of printable pages of the laser unit has reached the upper limit.

Error code 4B01

Dot counter or develop roller counter of the toner is reaching the upper limit.

Error code 4C01

Dot counter or develop roller counter of the toner has reached the upper limit.

Error code 4F01

The new toner sensor could not detect the new toner cartridge correctly.

Step

Cause

Remedy

1

End of life of the laser unit

Replace the laser unit. Refer to 

“1.3.22 Reset 

counters for consumable parts (function code: 
88)” in Chapter 5

 to reset the laser unit counter 

after the replacement.

2

Replace the laser unit with a 
new one and reset the laser unit 
counter. If the error display is not 
cleared, the main PCB is faulty.

Replace the main PCB ASSY.

Step

Cause

Remedy

1

Replace the toner cartridge with 
a new one. If the error display is 
not cleared, the main PCB is 
faulty.

Replace the main PCB ASSY.

<User Check>

• If the machine is on the uneven surface, place it on a level surface.

Step

Cause

Remedy

1

Connection failure of the relay 
front harness

Reconnect the relay front harness.

2

New toner actuator coming off 
or caught in some sections of 
the machine

Reattach the new toner actuator.

3

Develop joint coming off or 
caught in some sections of the 
machine

Reattach the develop joint.

4

New toner sensor failure

Replace the relay front PCB ASSY.

5

Paper feed drive gears failure

Replace the main frame L ASSY.

6

If the error display is not cleared 
after replacing the toner 
cartridge with a new one again, 
the main PCB is faulty.

Replace the main PCB ASSY.

Summary of Contents for HL-5580D


















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands