manualshive.com logo in svg

Broadcom BCM1125, User Manual

The Broadcom BCM1125 user manual is an essential guide to maximize your product usage. Unlock its full potential by downloading the comprehensive manual from our website for free. Discover detailed instructions, troubleshooting tips, and more to ensure seamless and hassle-free use of your Broadcom BCM1125.

Share
Download
background image

BCM1250/BCM1125/BCM1125H

User Manual

10/21/02

B r o a d c o m   C o r p o r a t i o n

Page  

440

Section 15: JTAG and Debug

 Document

1250_1125-UM100CB-R

7

PrAcc

Processor Access. Read value of this bit indicates if a Processor Access 
(PA) to the EJTAG memory is pending: 

0: No pending processor access. 

1: Pending processor access. 

The probe control software must clear this bit to 0 to indicate the end of the 
PA. Write of 1 is ignored.

R/W

0

8

PW

Processor Access Write. 

This bit is not used.

R/W

X

9

PbAcc

Probe Initiated Transaction. When set this bit indicates a probe initiated 
transaction is in progress. The probe sets this bit to indicate to the JTAG unit 
that the probe is initiating a transaction. The JTAG unit clears this bit when 
the transaction has been completed. This bit can only be set if the ProbEn bit 
is cleared. Probe initiated transactions can occur only if the MaSl bit is set. 

0: No pending probe access. 
1: Pending probe access.

If the probe writes a zero to this bit it is ignored. The only way the bit can be 
set is by the probe writing a 1, the only way the bit can be cleared is by the 
JTAG unit clearing it. 

R/W

0

10

MaSl

Probe Master/Slave. When set this bit indicates the probe can initiate a 
transaction, if ProbEn is set then CPU accesses will be blocked until this bit 
is clear. When clear CPU transactions will be accepted if ProbEn is set. 

0: CPU accesses accepted. 

1: Probe can initiate a bus transaction.

R/W

0

11

ClkStop

Clock stop flag. This bit is for Broadcom Use Only.

R/O

0

Table 310:  EJTAG Control Register

 (Cont.)

Bit

Name

Description

Use

Reset

Value

Summary of Contents for BCM1125





































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for BCM1125

3Com Token Ring Getting Started Manual preview
Token Ring
Brand: 3Com Pages: 18
Supermicro SC836 X9 User Manual preview
SC836 X9
Brand: Supermicro Pages: 24
hilscher CIFX 104 User Manual preview
CIFX 104
Brand: hilscher Pages: 154
QuickLink QL-CXS Installation Manual preview
QL-CXS
Brand: QuickLink Pages: 8
ADTRAN EXPRESS 6503 User Manual preview
EXPRESS 6503
Brand: ADTRAN Pages: 20
FiberHome AN5506-04-F User Manual preview
AN5506-04-F
Brand: FiberHome Pages: 2
UNICORECOMM UM620N User Manual preview
UM620N
Brand: UNICORECOMM Pages: 19
Keysight Technologies U3024AH10 User'S And Service Manual preview
U3024AH10
Brand: Keysight Technologies Pages: 106
Hanwha Techwin Wisenet PRN-6400DB4 User Manual preview
Wisenet PRN-6400DB4
Brand: Hanwha Techwin Pages: 125
JETWAY LI22 Series User Manual preview
LI22 Series
Brand: JETWAY Pages: 63
Trend Micro R610 Series Quick Start Manual preview
R610 Series
Brand: Trend Micro Pages: 2
nox Hummer H-240CL Manual preview
Hummer H-240CL
Brand: nox Pages: 16
Analog Devices EZ-KIT LITE ADSP-2191 Manual preview
EZ-KIT LITE ADSP-2191
Brand: Analog Devices Pages: 98
ICP DAS USA WF-2572M User Manual preview
WF-2572M
Brand: ICP DAS USA Pages: 26
Zmotion ZMIO300 Series Hardware Manual preview
ZMIO300 Series
Brand: Zmotion Pages: 56
SeaLevel 2423 User Manual preview
2423
Brand: SeaLevel Pages: 25
Citizen IF1-ET01 User Manual preview
IF1-ET01
Brand: Citizen Pages: 26
Crestron CAEN-CK-7x1 Quick Start Manual preview
CAEN-CK-7x1
Brand: Crestron Pages: 2

Brands by name

Popular brands

Load more brands