manualshive.com logo in svg

Broadcom BCM1125, User Manual

The Broadcom BCM1125 user manual is an essential guide to maximize your product usage. Unlock its full potential by downloading the comprehensive manual from our website for free. Discover detailed instructions, troubleshooting tips, and more to ensure seamless and hassle-free use of your Broadcom BCM1125.

Share
Download
background image

User Manual

BCM1250/BCM1125/BCM1125H

10/21/02

B r o a d c o m   C o r p o r a t i o n

Document

1250_1125-UM100CB-R

Section 7: DMA Page  

185

 

 

Table 116:  Data Mover Descriptor Count Register

dm_dscr_count_0 - 

00_1002_0B08

dm_dscr_count_1 - 

00_1002_0B28

dm_dscr_count_2 - 

00_1002_0B48

dm_dscr_count_3 - 

00_1002_0B68

Bits

Name

Default

Description

15:0 

count 

16'b0 

This is the number of descriptors owned by the DMA engine. Reads will return the number 
of unused descriptors. Data that is written to this register will be added to the count 
(assigning that number of additional descriptors to the controller). 

63:16

reserved

48’b0

Reserved

Table 117:  Data Mover Current Descriptor Address

dm_cur_dscr_addr_0 - 

00_1002_0B10

dm_cur_dscr_addr_1 - 

00_1002_0B30

dm_cur_dscr_addr_2 - 

00_1002_0B50

dm_cur_dscr_addr_3 - 

00_1002_0B70

READ ONLY

Bits

Name

Default

Description

39:0 

dscr_addr 

40'bx 

The current descriptor address can be read from this field. 

47:40 reserved  8'b0 

Reserved 

63:48 

cur_count 

16'b0 

The current count of descriptors owned by the DMA engine can be read from this field. 

Table 118:  Data Mover CRC Definition Registers (Only if System Revision >= PERIPH_REV3)

crc_def_0 - 

00_1002_0B80

crc_def_1 - 

00_1002_0B90

Bits

Name

Default

Description

31:0 

crc_init 

32'bx

This is the initial value for the partial CRC and is loaded into the partial result register before 
a move that has the crc_reset flag set. For CRCs smaller than 32 bits the initial value should 
be put into the high bits of this field and the low bits should be zeros.

63:32 

crc_poly 

32'bx

This is the polynomial used to define the CRC. For CRCs smaller than 32 bits the polynomial 
value should be put into the high bits of this field and the low bits should be zeros.

Summary of Contents for BCM1125





































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for BCM1125

National Instruments NI 9426 Getting Started Manual preview
NI 9426
Brand: National Instruments Pages: 17
Garland INT10G10SP2 User Manual preview
INT10G10SP2
Brand: Garland Pages: 6
Black Box JPM083A Manual preview
JPM083A
Brand: Black Box Pages: 9
Qlogic QLE7xxx Series Quick Start Manual preview
QLE7xxx Series
Brand: Qlogic Pages: 8
ZALMAN ZM-RF1 User Manual preview
ZM-RF1
Brand: ZALMAN Pages: 5
4gon RouterBOARD 411R Quick Start Manual preview
RouterBOARD 411R
Brand: 4gon Pages: 2
Tait TM9000 Installation Instructions Manual preview
TM9000
Brand: Tait Pages: 8
C4i GEN-1 Quick Operation Manual preview
GEN-1
Brand: C4i Pages: 5
Supero SAS 846 TQ User Manual preview
SAS 846 TQ
Brand: Supero Pages: 16
Renesas REJ06B0734-0100 Application Note preview
REJ06B0734-0100
Brand: Renesas Pages: 19
AMX AXB-PSCV Dimensional Drawing preview
AXB-PSCV
Brand: AMX Pages: 1
Renesas R0E001000ACB00 User Manual preview
R0E001000ACB00
Brand: Renesas Pages: 4
SilverStone GD05 Manual preview
GD05
Brand: SilverStone Pages: 28
iesy Open Standard Module RPX30 EVA-MI V1 Quick Start Manual preview
Open Standard Module RPX30 EVA-MI V1
Brand: iesy Pages: 9
ADLINK Technology cPCIS-1100 Series User Manual preview
cPCIS-1100 Series
Brand: ADLINK Technology Pages: 48
Xcellon DRD-501 User Manual preview
DRD-501
Brand: Xcellon Pages: 24
Idis DR-8364F Quick Manual preview
DR-8364F
Brand: Idis Pages: 16
ADTRAN Total Access 1500 Dual FXS/DPO Quick Start Manual preview
Total Access 1500 Dual FXS/DPO
Brand: ADTRAN Pages: 2

Brands by name

Popular brands

Load more brands