manualshive.com logo in svg

Broadcom BCM1125, User Manual

The Broadcom BCM1125 user manual is an essential guide to maximize your product usage. Unlock its full potential by downloading the comprehensive manual from our website for free. Discover detailed instructions, troubleshooting tips, and more to ensure seamless and hassle-free use of your Broadcom BCM1125.

Share
Download
background image

BCM1250/BCM1125/BCM1125H

User Manual

10/21/02

B r o a d c o m   C o r p o r a t i o n

Page  

442

Section 15: JTAG and Debug

 Document

1250_1125-UM100CB-R

5.5.4

The address register is 77 bits (contains ZBbus a cmd)

5.5.5

Rocc - Not implemented
Psz  - Not implemented, size in address register
Doze - Not implemented
Halt - Not implemented
PerRst - Use System Config register for resets
PRnW - Not used
PrAcc - Supported
PrRst - Use System Config register for resets
ProbEn - Supported (works with additional MaSl bit to set direction)
ProbTrap - Two Copies, one per CPU. Also causes EJTAG boot on reset
EjtagBrk - Two Copies, one per CPU, level sensitive probe must clear
DM - Two copies. But shows CPU EDEN signal rather than DM

5.6.3

Rocc is not supported

5.6.4

Processor access is through physical address 00_1000_0000 - 00_1001_FFFF and uses ZBbus
request

There is an additional mode for allowing the probe to initiate bus requests to memory or memory mapped
I/O.

7.1.2

External interrupt possible through DEBUG_L pin but the driver must be open collector or open drain.

7.1.2

The probe RST signal can be connected to RESET_L.

Summary of Contents for BCM1125





































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for BCM1125

Omnia 11 Installation And Operation Manual preview
11
Brand: Omnia Pages: 102
Udoo NEO Step-By-Step Manual preview
NEO
Brand: Udoo Pages: 7
Black Box JPM083A Manual preview
JPM083A
Brand: Black Box Pages: 9
PairGain PG-FLEX RT FRL-752 Manual preview
PG-FLEX RT FRL-752
Brand: PairGain Pages: 6
vPipes Uilleann Quick Start Manual preview
Uilleann
Brand: vPipes Pages: 3
Cromemco 32K Bytesaver Instruction Manual preview
32K Bytesaver
Brand: Cromemco Pages: 46
Verizon Wireless PC 3220 Owner'S Manual preview
PC 3220
Brand: Verizon Wireless Pages: 39
Novus NVIP- NVRA0104/GO User Manual preview
NVIP- NVRA0104/GO
Brand: Novus Pages: 44
Seattle Computer Products 8086 CPU Instruction Manual preview
8086 CPU
Brand: Seattle Computer Products Pages: 31
ATI Technologies RADEON 9800 PRO Getting Started Manual preview
RADEON 9800 PRO
Brand: ATI Technologies Pages: 20
Xantech IR-X10 Installation Instructions Manual preview
IR-X10
Brand: Xantech Pages: 16
Keithley DAS-1800HR Series User Manual preview
DAS-1800HR Series
Brand: Keithley Pages: 139
8e6 Technologies HL-002-006 Quick Start Manual preview
HL-002-006
Brand: 8e6 Technologies Pages: 94
ZALMAN CNPS9500 AT User Manual preview
CNPS9500 AT
Brand: ZALMAN Pages: 9
YASKAWA 040-1CA00 Manual preview
040-1CA00
Brand: YASKAWA Pages: 87
LanReady AP-952X User Manual preview
AP-952X
Brand: LanReady Pages: 40
StetSom STX2448 User Manual preview
STX2448
Brand: StetSom Pages: 18
ADTRAN NetVanta 1224R Specifications preview
NetVanta 1224R
Brand: ADTRAN Pages: 4

Brands by name

Popular brands

Load more brands