manualshive.com logo in svg

Broadcom BCM1125, User Manual

The Broadcom BCM1125 user manual is an essential guide to maximize your product usage. Unlock its full potential by downloading the comprehensive manual from our website for free. Discover detailed instructions, troubleshooting tips, and more to ensure seamless and hassle-free use of your Broadcom BCM1125.

Share
Download
background image

User Manual

BCM1250/BCM1125/BCM1125H

10/21/02

B r o a d c o m   C o r p o r a t i o n

Document

1250_1125-UM100CB-R

Section 6: DRAM Page  

137

52

iob1_priority

1’b1

mc_config_1

: If this bit is set reads from I/O bridge 1 will be given high priority (to 

reduce their latency). If clear all requests have the same priority.

mc_config_0

: Reserved.

55:53

reserved

3’b0

Reserved

59:56

cs_mode

4’h0

mc_config_1

: Chip Selection mode 

0000: msb-CS mode: CS[3:0]are determined by the corresponding CS start/end+1 

address registers. 

1111: Interleaved-CS mode: the values of start/end+1 addresses of CS[3:0] are all 

same in this mode, CS[3:0] are decoded by the two bits in the interleaved CS 
position register.

1100: Mixed-CS mode: CS[1] and CS[0] are not interleaved and determined by the 

corresponding start/end+1 addresses. The interleaving occurs between CS3 
and CS2, determined by one bit of the interleaved CS position register. The 
values of the CS[3:2] start/end+1 addresses are the same. 

0110: Mixed-CS mode: CS[3] and CS[0] are not interleaved and determined by the 

corresponding start/end+1 addresses.Tthe interleaving occurs between CS2 
and CS1, determined by one bit of the interleaved CS position register. The 
values of the CS[2:1] start/end+1 addresses are the same. 

0011: Mixed-CS mode: CS[3] and CS[2] are not interleaved and determined by the 

corresponding start/end+1 addresses. The interleaving occurs between CS1 
and CS0, determined by one bit of the interleaved CS position register. The 
values of the CS[1:0] start/end+1 addresses are the same. 

mc_config_0

: Reserved.

60

ecc_disable

1’b0

mc_config_1

: ECC disable. If this bit is set ECC checking will not be performed 

and data will never be reported to have an error.

mc_config_0

: Reserved.

61

berr_disable

1’b0

mc_config_1

: Bus error disable. This bit sets the behavior when a read is done to 

an address that does not match any chip select range. 
0: Generate a bus error data return
1: Generate a valid data return containing UNPREDICTABLE data.

mc_config_0

: Reserved.

62

force_seq

1’b0

mc_config_1

: Force Sequential. If this bit is set requests will be issued to memory 

in the same order their A-phase happens on the ZBbus.

mc_config_0

: Reserved.

63

reserved

1’b0

Reserved

Table 73:  Memory Channel Configuration Register on BCM1125/H

 (Cont.)

mc_config_0 - 

00_1005_1100

mc_config_1 - 

00_1005_2100

Bits

Name

Default

Description

Summary of Contents for BCM1125





































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for BCM1125

XDS 910 Reference Manual preview
910
Brand: XDS Pages: 99
Vivotek NR8401 User Manual preview
NR8401
Brand: Vivotek Pages: 136
Barco ImagePRO-HD Installation Manual preview
ImagePRO-HD
Brand: Barco Pages: 121
C&T Solution RCO-3000 Series User Manual preview
RCO-3000 Series
Brand: C&T Solution Pages: 96
Glacier G2080TiFE Installation Manual preview
G2080TiFE
Brand: Glacier Pages: 2
LevelOne FSW-0808TX Quick Start Manual preview
FSW-0808TX
Brand: LevelOne Pages: 3
SilverStone GD05 Manual preview
GD05
Brand: SilverStone Pages: 28
Paradyne 8310 MVLt User Manual preview
8310 MVLt
Brand: Paradyne Pages: 108
DPS Telecom D-PK-NG432 User Manual preview
D-PK-NG432
Brand: DPS Telecom Pages: 80
Moxa Technologies CP-102N-T Quick Installation Manual preview
CP-102N-T
Brand: Moxa Technologies Pages: 8
Siklu EtherHaul 500 Installation Manual preview
EtherHaul 500
Brand: Siklu Pages: 52
Kontron KISS Stor Slim Quick Installation Manual preview
KISS Stor Slim
Brand: Kontron Pages: 4
Nortel 1000 Con?guration guide Installation And Commissioning Manual preview
1000 Con?guration guide
Brand: Nortel Pages: 108
Optimus UMX-2M3 Operating Instructions Manual preview
UMX-2M3
Brand: Optimus Pages: 15
8e6 Technologies TAR "MSA" Evaluation Manual preview
TAR "MSA"
Brand: 8e6 Technologies Pages: 22
dbx 166 Service Manual preview
166
Brand: dbx Pages: 26
dbx IEM User Manual preview
IEM
Brand: dbx Pages: 58
dbx Zone Pro 1260 User Manual preview
Zone Pro 1260
Brand: dbx Pages: 75

Brands by name

Popular brands

Load more brands