Error code
Cause
Remedy
E 1.1
Error in handling the probe during
measurement (contact time greater than 3
seconds)
Repeat the measurement.
Ensure correct probe handling.
Place the probe with the nececcary pressure
carefully onto the material surface.
E 1.2
Measurement cannot be evaluated (e.g. if
used probe is not suitable for test material).
Repeat measurement.
If necessary, use another probe.
E 1.3
The probe was coupled before termination
of a defined measurement time.
Repeat measurement.
Note the symbol in the MIC 10 display.
E 2.0
Error when reading the Memory Card.
Remove the Memory Card and reinsert it again.
If the error reoccurs, use another Memory Card.
E 2.1
Memory Card written by the DynaMIC
Delete data or use another Memory Card.
E 3.0
Interface is not ready.
Check to see if your printer or PC is correctly
connected.
The MIC 10 gives additional text error messages:
OFL / UFL
Overflow / Underflow
Out of range when hardness scale is
changed.
Select another hardness scale.
Full
Not enough storage capacity for the data
to be stored.
Delete the contents of the Data Logger or
Memory Card (if necessary, after previous
transfer to a PC) or use another Memory Card.
Function check and troubleshooting
Troubleshooting
9-4
Issue 08, 08/01
Krautkrämer MIC 10
Error code
Cause
Remedy
E 1.1
Error in handling the probe during
measurement (contact time greater than 3
seconds)
Repeat the measurement.
Ensure correct probe handling.
Place the probe with the nececcary pressure
carefully onto the material surface.
E 1.2
Measurement cannot be evaluated (e.g. if
used probe is not suitable for test material).
Repeat measurement.
If necessary, use another probe.
E 1.3
The probe was coupled before termination
of a defined measurement time.
Repeat measurement.
Note the symbol in the MIC 10 display.
E 2.0
Error when reading the Memory Card.
Remove the Memory Card and reinsert it again.
If the error reoccurs, use another Memory Card.
E 2.1
Memory Card written by the DynaMIC
Delete data or use another Memory Card.
E 3.0
Interface is not ready.
Check to see if your printer or PC is correctly
connected.
The MIC 10 gives additional text error messages:
OFL / UFL
Overflow / Underflow
Out of range when hardness scale is
changed.
Select another hardness scale.
Full
Not enough storage capacity for the data
to be stored.
Delete the contents of the Data Logger or
Memory Card (if necessary, after previous
transfer to a PC) or use another Memory Card.
Function check and troubleshooting
Troubleshooting
9-4
Issue 08, 08/01
Krautkrämer MIC 10
Summary of Contents for Krautkramer MIC 10
