Measuring with defined measurement
times (dwell time)
As opposed to short time measurements, you can
carry out measurements whose dwell time you can
determine yourself. In order to measure with a steady
accuracy you require a cylindrical probe attachment
as well as a test support.
You can set a dwell time between 1-99 seconds.
Setting the dwell time
–
Press
M
until the following indication appears in the
display:
–
Set the required dwell time with
^8
, for example:
–
Press
-
if you wish to return to the measurement
mode or simply carry out a measurement.
Carrying out a measurement
–
Screw on the cylindrical attachment tightly down to
screw stop on the probe case.
–
Clamp the probe into the support (DH 191 or
MIC 222). By doing this you will avoid measurement
inaccuracies.
–
Select the required hardness scale.
–
If necessary set the calibration value and the alarm
threshold.
–
Carry out the measurement.
–
Make certain that the tip of the probe attachment is
pressed on the material to be measured during the
complete measurement time.
Operation
Hardness measurement
5-18
Issue 08, 08/01
Krautkrämer MIC 10
Measuring with defined measurement
times (dwell time)
As opposed to short time measurements, you can
carry out measurements whose dwell time you can
determine yourself. In order to measure with a steady
accuracy you require a cylindrical probe attachment
as well as a test support.
You can set a dwell time between 1-99 seconds.
Setting the dwell time
–
Press
M
until the following indication appears in the
display:
–
Set the required dwell time with
^8
, for example:
–
Press
-
if you wish to return to the measurement
mode or simply carry out a measurement.
Carrying out a measurement
–
Screw on the cylindrical attachment tightly down to
screw stop on the probe case.
–
Clamp the probe into the support (DH 191 or
MIC 222). By doing this you will avoid measurement
inaccuracies.
–
Select the required hardness scale.
–
If necessary set the calibration value and the alarm
threshold.
–
Carry out the measurement.
–
Make certain that the tip of the probe attachment is
pressed on the material to be measured during the
complete measurement time.
Operation
Hardness measurement
5-18
Issue 08, 08/01
Krautkrämer MIC 10
Summary of Contents for Krautkramer MIC 10
