Bosch Rexroth IndraMotion MTX 11 VRS Applications Manual Download Page 279

Page: 279 / 304

Fig.11-30:

Form for using the tolerance dimension table

Preference Tolerances

The following tolerance fields are listed for shafts:
a11, c11, d9, e8, f7, f8, g6, h5, h6, h9, h11, j6, k6, n5, m6, n6, r5, r6, s6, s8, u8,

x8, and x11.
The following tolerance fields are listed for holes:
A11, C11, D10, E9, F7, F8, G6, G7, H6, H7, H8, H11, J6, J7, K7, M6, M7, N6,

N7, P6, R7, S7, X9, and X11

Finding an Allowance

Entering nominal size and toler‐

ance field

Enter the nominal size followed by the tolerance field. In this connection, spaces

are admissible. Expressions are not allowed.
Example:

Allowances for a hole: 60 H6
Allowances for a shaft: 22.5 f8

Using the return key or by changing the focus, the determination of the allow‐

ance is initiated.

Transferring the Allowance

Select one of the three listed allowances and press "Copy".

Error

Error causes

The following causes in the entry can be considered:
●

Invalid specification,

DOK-MTX***-NC*OP***V11-AP01-EN-P
Rexroth IndraMotion MTX 11VRS Standard NC Operation

Bosch Rexroth AG

277/301

Extended Functionality

Summary of Contents for Rexroth IndraMotion MTX 11 VRS

















































































































































































































































































































Search results

Summary of Contents for Rexroth IndraMotion MTX 11 VRS

Reviews:

Bosch Rexroth IndraMotion MTX 11 VRS, Applications Manual, Page: 279 / 304

Search results

Summary of Contents for Rexroth IndraMotion MTX 11 VRS

Reviews: