Bosch Rexroth IndraMotion MTX 11 VRS Applications Manual Download Page 254

Page: 254 / 304

Configuration of the Power Monitor - General

Fig.11-14:

Configuration of the power monitor - General

Under "General", the maximum total drive power and the maximum single drive

power have to be entered. Additionally, the display sequence of the drives as

well as of the auxiliary equipments can be specified for the different power dis‐

plays using the arrow keys if required.

11.3.3

Working with the Power Monitor

Starting the Power Monitor

In the basic default screen, the power monitor can be shown via the second F-

key level with <F7> and <F3> if required.
The power monitor can also be configured in the user screens on F-keys or M-

keys.

Bosch Rexroth AG

DOK-MTX***-NC*OP***V11-AP01-EN-P

Rexroth IndraMotion MTX 11VRS Standard NC Operation

252/301

Extended Functionality

Summary of Contents for Rexroth IndraMotion MTX 11 VRS

















































































































































































































































































































Search results

Summary of Contents for Rexroth IndraMotion MTX 11 VRS

Reviews:

Bosch Rexroth IndraMotion MTX 11 VRS, Applications Manual, Page: 254 / 304

Search results

Summary of Contents for Rexroth IndraMotion MTX 11 VRS

Reviews: