Bosch Rexroth IndraMotion MTX 11 VRS Applications Manual Download Page 205

Page: 205 / 304

Fig.10-16:

Profibus DP diagnostic overview screen

The detail view provides additional information on each bus device. The detail

view is available for each slave. The detail view is displayed for the bus device

selected (with black borders). There are three ways of opening the detail view:
●

Left-click on the slave desired.

●

Use the arrow keys to select the slaves desired and confirm with <EN‐

TER>.

●

Use the arrow keys to select the slaves desired and confirm with <F9>.

Press <F9> to switch between the overview and detail views.
After you have pressed the key, the detail view will appear on the central and

lower areas of the overview screen. This view provides information on the cur‐

rent state of the bus device, the slave address and the ident number and the

station status. In case of error, the current error number transferred by the con‐

trol and the hexadecimal-encoded channel error text are displayed.

DOK-MTX***-NC*OP***V11-AP01-EN-P
Rexroth IndraMotion MTX 11VRS Standard NC Operation

Bosch Rexroth AG

203/301

Diagnostics

Summary of Contents for Rexroth IndraMotion MTX 11 VRS

















































































































































































































































































































Search results

Summary of Contents for Rexroth IndraMotion MTX 11 VRS

Reviews:

Bosch Rexroth IndraMotion MTX 11 VRS, Applications Manual, Page: 205 / 304

Search results

Summary of Contents for Rexroth IndraMotion MTX 11 VRS

Reviews: