manualshive.com logo in svg

Bosch Rexroth IndraMotion MTX 11 VRS, Applications Manual, Page: 209 / 304

Share
Download
Bosch Rexroth IndraMotion MTX 11 VRS Applications Manual Download Page 209

<F2>

<F3>

<F4>

<F5>

<F6>

<F7>

<F8>

<F9>

S

Spindle -

 

 

Spindle -
Selection

Focus
Change

 

Basic
Level

Fig.10-23:

F-keys spindle signals

Pressing <F2> or <F3> displays the interface of the next/previous spindle.
Pressing <F6> displays a dialog for selecting spindles.
Pressing <F7> switches the focus between the lists.
Pressing <F9> jumps back to the basic level.

F-keys global signals

.

<F2>

<F3>

<F4>

<F5>

<F6>

<F7>

<F8>

<F9>

 

 

 

 

 

Focus
Change

 

Basic
Level

Fig.10-24:

F-keys global signals

Pressing <F7> switches the focus between the lists.
Pressing <F9> jumps back to the basic level.

F-keys combined display

In the combined display, <F8> is also assigned to the "Signal type selection"

function. Pressing this key opens a dialog in which the signal types for the left

and right list can be selected.

10.5 

Variable Lists and Parameter Lists

10.5.1 

Usage

The application shows selected variables and parameters in a pre-configured

list of 22 lines and 5 columns.
The values of these variables and parameters can be changed online within the

list.

Categories and Subcategories

Categories and subcategories of variables and parameters are shown in the

following table.

Symbol

Category

Subcategory

NC variables

CPL variables
SD variables

PLC variables

All data types
such as bool, integer etc.

Machine Parameters

All parameter types
Such as axis parameters, spindle param‐

eters, channel parameters

Drive parameters

Data
Status

Fig.10-25:

Categories and Subcategories

DOK-MTX***-NC*OP***V11-AP01-EN-P 
Rexroth IndraMotion MTX 11VRS Standard NC Operation 

Bosch Rexroth AG

207/301

Diagnostics

Summary of Contents for Rexroth IndraMotion MTX 11 VRS

















































































































































































































































































































Reviews:

No comments