Bosch Rexroth IndraDrive CsDrive System with HCS01 Project Planning Manual Download Page 264

Page: 264 / 344

Battery

Type: ER6C, 3.6 V; 1800 mA, lithium
Lifetime: Depends on load and ambient temperature

Standby mode using battery with a battery current of 90 µA

Batt

Battery current

Batt

Battery lifetime in years

Drive controller On time

off

Drive controller Off time

Fig. 8-18:

Battery lifetime depending on load

Example: With a relation t

off

= 5 (every day, drive controller is on for 20 hours and

off for 4 hours), the battery lifetime is approx. 9 years.

Refresh resistor

10 ohm; the refresh resistor is used to prepare the battery before the battery is used

in the battery box "

SUP-E01-MSM-BATTERYBOX

Documentation
(DOZ-SUPPL*-SUP-E03-DKC-

MA01-D5-P)

Information in 5 languages on the refresh procedure of the battery and on how to

connect the battery and the base load resistor.

Base load resistor

The base load resistor (500 kOhm) is only relevant to EcoDrive Cs drive controllers

(when they are operated without the SUP-E01-MSM-BATTERYBOX battery box).

Tab. 8-6:

SUP-E03-DKC*CS-BATTRY - content

Bosch Rexroth AG

DOK-INDRV*-HCS01******-PR05-EN-P

262/341

Rexroth IndraDrive CsDrive Systems with HCS01

Cables, accessories, additional components

Summary of Contents for Rexroth IndraDrive CsDrive System with HCS01

























































































































































































































































































































































Search results

Summary of Contents for Rexroth IndraDrive CsDrive System with HCS01

Reviews:

Related manuals for Rexroth IndraDrive CsDrive System with HCS01

Brands by name

Popular brands

Bosch Rexroth IndraDrive CsDrive System with HCS01, Project Planning Manual

Search results

Summary of Contents for Rexroth IndraDrive CsDrive System with HCS01

Reviews:

Related manuals for Rexroth IndraDrive CsDrive System with HCS01

Brands by name

Popular brands