Bosch Rexroth IndraDrive CsDrive System with HCS01 Project Planning Manual Download Page 312

Page: 312 / 344

Dimensions

Minimum mounting clearance

Boring dimensions

Fig. 8-59:

Dimensions

Connection

Lethal electric shock by live parts with more

than 50 V!

WARNING

Before working on live parts: De-energize installation and secure power

switch against unintentional or unauthorized re-energization.
Wait at least 30 minutes after switching off the supply voltages to allow dis‐

charging.
Check whether voltage has fallen below 50 V before touching live parts!

Fig. 8-60:

Connection points (DC Bus (L+ L-), equipment grounding conductor)

Bosch Rexroth AG

DOK-INDRV*-HCS01******-PR05-EN-P

310/341

Rexroth IndraDrive CsDrive Systems with HCS01

Cables, accessories, additional components

Summary of Contents for Rexroth IndraDrive CsDrive System with HCS01

























































































































































































































































































































































Search results

Summary of Contents for Rexroth IndraDrive CsDrive System with HCS01

Reviews:

Related manuals for Rexroth IndraDrive CsDrive System with HCS01

Brands by name

Popular brands

Bosch Rexroth IndraDrive CsDrive System with HCS01, Project Planning Manual

Search results

Summary of Contents for Rexroth IndraDrive CsDrive System with HCS01

Reviews:

Related manuals for Rexroth IndraDrive CsDrive System with HCS01

Brands by name

Popular brands