Bosch Rexroth IndraDrive CsDrive System with HCS01 Project Planning Manual Download Page 9

Page: 9 / 344

Page

7.3.3

DC bus............................................................................................................................................. 240

7.3.4

Integrated braking resistor............................................................................................................... 242

7.3.5

Inverter............................................................................................................................................ 243

Cables, accessories, additional components............................................................. 249

8.1

Overview............................................................................................................................................. 249

8.1.1

Cables............................................................................................................................................. 249

8.1.2

Accessories..................................................................................................................................... 249

8.1.3

Additional Components................................................................................................................... 250

8.2

Accessories........................................................................................................................................ 251

8.2.1

Mounting and connection accessories (HAS09).............................................................................. 251

8.2.2

DC Bus Connector (RLS0778/K06)................................................................................................. 258

8.2.3

Battery box SUP-E01-MSM-BATTERYBOX................................................................................... 259

8.2.4

Battery and refresh resistor (SUP-E03-DKC*CS-BATTRY)............................................................ 261

8.2.5

SUP-E02-MSM-BATTERYBOX battery box.................................................................................... 266

8.2.6

Encoder cable for MSM motors with absolute value encoder M0 (RKG0041)................................ 268

8.2.7

D-Sub Connector for Encoder Cable and Battery Connection (RGS0001/K01).............................. 274

8.2.8

Encoder cable for MSM motors with absolute value encoder M5 (RKG0065)................................ 278

8.2.9

RKB0011, Multi-Ethernet Cable...................................................................................................... 279

8.2.10

RKB0013, Multi-Ethernet Cable...................................................................................................... 280

8.2.11

Hall Sensor Adapter Box (SHL03.1-NNN-S-NNN).......................................................................... 281

8.2.12

Snap-on ferrite (HAS05.1-015)........................................................................................................ 287

8.3

Additional components....................................................................................................................... 290

8.3.1

Transformers................................................................................................................................... 290

General information...................................................................................................................... 290
Autotransformers for drive controllers.......................................................................................... 290

Types......................................................................................................................................... 290
Selected transformers............................................................................................................... 291

8.3.2

Mains Filters NFD / NFE.................................................................................................................. 292

Type Code NFE / NFD................................................................................................................. 292

NFE02.1 - Mains Filter, Single-Phase....................................................................................... 292
NFD03.1 - Mains Filter, Three-Phase........................................................................................ 292

Mechanical Data NFE / NFD........................................................................................................ 293

NFE02.1.................................................................................................................................... 293
NFD03.1.................................................................................................................................... 294

Electrical Data NFE / NFD............................................................................................................ 295

8.3.3

Mains chokes................................................................................................................................... 297

DOK-INDRV*-HCS01******-PR05-EN-P

Bosch Rexroth AG

VII/341

Rexroth IndraDrive CsDrive Systems with HCS01

Table of Contents

Summary of Contents for Rexroth IndraDrive CsDrive System with HCS01

























































































































































































































































































































































Search results

Summary of Contents for Rexroth IndraDrive CsDrive System with HCS01

Reviews:

Related manuals for Rexroth IndraDrive CsDrive System with HCS01

Brands by name

Popular brands

Bosch Rexroth IndraDrive CsDrive System with HCS01, Project Planning Manual

Search results

Summary of Contents for Rexroth IndraDrive CsDrive System with HCS01

Reviews:

Related manuals for Rexroth IndraDrive CsDrive System with HCS01

Brands by name

Popular brands