Bosch Rexroth IndraDrive CsDrive System with HCS01 Project Planning Manual Download Page 140

Page: 140 / 344

X6, Motor Temperature Monitoring and Motor Holding Brake

Dangerous movements! Danger to persons

from falling or dropping axes!

WARNING

The standard motor holding brake provided or an external motor holding

brake controlled directly by the drive controller are not sufficient on their own

to guarantee personal safety!
Personal safety must be achieved using higher-level, fail-safe measures:
●

Block off danger zones with safety fences or safety guards

●

Additionally secure vertical axes against falling or dropping after switch‐

ing off the motor power by, for example,
–

mechanically securing the vertical axes

–

adding external braking/arrester/clamping mechanisms

–

ensuring sufficient equilibration of the vertical axes

Lethal electric shock by live parts with more

than 50 V!

WARNING

The input of the motor temperature evaluation is not galvanically isolated

from the housing. If the voltage applied to the input is impermissibly high (e.g.

because of a flashover of the motor winding voltage), this voltage may come

into contact with the housing. Ensure that the temperature sensor of the con‐

nected motor has a double isolation against the motor winding.

Excessive voltage at the input of the motor

temperature evaluation may cause damage

to the device!

NOTICE

The voltage allowed at the input of the motor temperature evaluation must

correspond to the allowed control voltage of the device. If the voltage applied

to the input is impermissibly high, the device may be damaged.

Function

Connection point X6 contains the connections for
●

monitoring the motor temperature

●

controlling the motor holding brake

Via an integrated contact element (BR), the power section

switches the voltage of the external 24-V supply to the output for

controlling the motor holding brake.

View

Connec‐

tion

Signal name

Function

Motor temperature evaluation in‐

put

MotTemp-

+24VBr

Output for controlling the motor

holding brake

0VBr

Bosch Rexroth AG

DOK-INDRV*-HCS01******-PR05-EN-P

138/341

Rexroth IndraDrive CsDrive Systems with HCS01

Mounting and installation

Summary of Contents for Rexroth IndraDrive CsDrive System with HCS01

























































































































































































































































































































































Search results

Summary of Contents for Rexroth IndraDrive CsDrive System with HCS01

Reviews:

Related manuals for Rexroth IndraDrive CsDrive System with HCS01

Brands by name

Popular brands

Bosch Rexroth IndraDrive CsDrive System with HCS01, Project Planning Manual

Search results

Summary of Contents for Rexroth IndraDrive CsDrive System with HCS01

Reviews:

Related manuals for Rexroth IndraDrive CsDrive System with HCS01

Brands by name

Popular brands