manualshive.com logo in svg

Bosch Rexroth IndraDrive CsDrive System with HCS01, Project Planning Manual

The Bosch Rexroth IndraDrive CsDrive System with HCS01 is a cutting-edge industrial automation solution. Unlock its full potential by following the comprehensive and user-friendly Instruction Manual, available for free download on our website. Elevate your operations with precise control and optimized performance.

Share
Download
background image

X9, integrated/external braking resistor

Lethal  electric  shock  by  live  parts  with  more

than 50 V!

WARNING

Exclusively operate the device
●

with plugged on connectors (even if there haven't been any lines con‐

nected to the connectors) and

●

with connected equipment grounding conductor!

Function

X9  is  used  to  connect  the  integrated  or  external  braking  resistor  HLR.  By

means of an internal switch, the braking resistor is connected to the DC bus.

Parameterize the external braking resistor by means of the firm‐

ware  to  protect  the  drive  controller  and  the  braking  resistor

against overload:
●

P-0-0860, Converter configuration

●

P-0-0858, Data of external braking resistor

 

Connection (HCS01.1E-W0003…

W0028)

Fig. 6-7:

Connecting the braking resistor (HCS01.1E-W0003…W0028)

 

Connection (HCS01.1E-W0054)

Fig. 6-8:

Connecting the braking resistor (HCS01.1E-W0054)

 

Notes on installation

Maximum allowed line length to external braking resistor: 5 m
Twist unshielded lines.

DOK-INDRV*-HCS01******-PR05-EN-P 

Bosch Rexroth AG

141/341

Rexroth IndraDrive CsDrive Systems with HCS01

Mounting and installation

Summary of Contents for Rexroth IndraDrive CsDrive System with HCS01

























































































































































































































































































































































Reviews:

No comments

Related manuals for Rexroth IndraDrive CsDrive System with HCS01

3M PX5 Series Reference Manual preview
PX5 Series
Brand: 3M Pages: 34
Parker ER Series Maintenance Instructions & Parts List preview
ER Series
Brand: Parker Pages: 44
hager tebis TX100 Operating Manual preview
tebis TX100
Brand: hager Pages: 62
hager coviva Smartbox TKP100A Configuration Manual preview
coviva Smartbox TKP100A
Brand: hager Pages: 45
L. G. B. 51099 Instructions preview
51099
Brand: L. G. B. Pages: 2
L-Acoustics LA4X Product Information preview
LA4X
Brand: L-Acoustics Pages: 36
Rain Bird STP-400i Installation, Programming & Operation Manual preview
STP-400i
Brand: Rain Bird Pages: 20
Balboa Revolution System Overview Manual preview
Revolution
Brand: Balboa Pages: 74
Cadac 343 User Instructions preview
343
Brand: Cadac Pages: 4
Balboa Water Group BP500 Troubleshooting Manual preview
BP500
Brand: Balboa Water Group Pages: 88
ABB A3 Series Instruction Sheet preview
A3 Series
Brand: ABB Pages: 2
Vizio Xrt302 Manual preview
Xrt302
Brand: Vizio Pages: 65
Allen-Bradley 1756-L72EROM Installation Instructions Manual preview
1756-L72EROM
Brand: Allen-Bradley Pages: 16
D+H RCM 230-11-U Original Instructions preview
RCM 230-11-U
Brand: D+H Pages: 2
Baier 50VA Instruction Manual preview
50VA
Brand: Baier Pages: 20
Harman Martin M2GO HD Safety And Installation Manual preview
Martin M2GO HD
Brand: Harman Pages: 20
Varian Turbo-V 250 series Instruction Manual preview
Turbo-V 250 series
Brand: Varian Pages: 79
M-system R7M-DC16B Instruction Manual preview
R7M-DC16B
Brand: M-system Pages: 7

Brands by name

Popular brands

Load more brands