Black Box LWE120A User Manual Download Page 79 | Manualshive

Page: 79 / 88

background image

724-746-5500 | blackbox.com

Page 79

Chapter 5: Navigate the Web Configurator

Figure 5-68. Wireless Broadband Access Point screen.

Enter the MAC address of another AP you wirelessly want to connect to into the appropriate field and click “Apply” to save the
settings.

NOTES:

WDS Settings is available only under Bridge and AP Repeater Mode.

Bridge uses the WDS protocol that is not defined as the standard, so compatibility issues between equipment from different
vendors may arise. Moreover, Tree or Star shape network topology should be used in all WDS use-cases (i.e. if AP2 and AP3 are
specified as the WDS peers of AP1, AP2 should not be specified as the WDS peer of AP3 and AP3 should not be specified as the
WDS peer of AP2 in any case). Mesh and Ring network topologies are not supported by WDS and should be avoided in all the
use cases.

5.3.4 Management

Password

From the “Password Settings” screen in “Management,” you can change the password to manage your Wireless Ethernet
Extender.

Figure 5-69. Password Settings screen.

«
...
77
78
79
80
81
...
»

Summary of Contents for LWE120A

























































































Reviews:

No comments

Related manuals for LWE120A

PRO MEGAMIX HPB300

Brand: Waring Pages: 8

Brand: Waring Pages: 7

Brand: HOME8 Pages: 6

Mini-Cat UH-1BTX

Brand: Hall Research Technologies Pages: 12

Brand: SOLAC Pages: 80

Brand: PourXuan Pages: 4

Brand: Elvira Pages: 9

Brand: Smeg Pages: 9

Brand: Navitar Pages: 1

Brand: WILSON PRO Pages: 40

Brand: Cisco Pages: 2

Brand: Electrolux Pages: 36

Brand: Electrolux Pages: 32

Brand: Electrolux Pages: 40

Brand: Electrolux Pages: 21

Brand: Electrolux Pages: 36

Brand: Electrolux Pages: 44

Brand: Electrolux Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands