Black Box LWE120A User Manual Download Page 75 | Manualshive

Page: 75 / 88

background image

724-746-5500 | blackbox.com

Page 75

Chapter 5: Navigate the Web Configurator

IGMP Snooping

Available in AP/Router mode, IGMP snooping is the process of listening to IGMP network traffic. By enabling IGMP snooping, the
AP will listen to IGMP membership reports, queries, and leave messages to identify the ports that are members of multicast
groups. Multicast traffic will only be forwarded to ports identified as members of the specific multicast group or groups.

RIFS

RIFS (Reduced Interframe Spacing) reduces overhead, thereby increasing network efficiency.

Link Integration

Available under AP/Bridge/AP repeater mode, this monitors the connection on the Ethernet port by checking “Enabled.” It can
inform the associating wireless clients as soon as the disconnection occurs.

TDM Coordination

Stands for “Time-Division Multiplexing Technique,” this resource reservation control mechanisms can avoid packet collisions and
send the packets much more efficiently allowing for higher effective throughput rates. This function is only available in AP/CPE
mode. We highly recommend enabling TDM coordination when there are multiple CPEs needed to connect to the AP in your
application.

LAN2LAN CPE

LAN2LAN CPE mode enables packet forwarding at layer 2 level. It is fully transparent for all the Layer 2 protocols.

Space in Meter

To decrease the chances of data retransmission at long distance, the Wireless Ethernet Extender can automatically adjust proper
ACK timeout value by specifying distance of the two nodes.

Flow Control

This allows the administrator to specify the incoming and outgoing traffic limit by checking “Enable Traffic Shaping.” This is only
available in Router mode.

NOTE: We strongly recommend you leave most advanced settings at their defaults except “Distance in Meters.” Adjust this
parameter for real distance; any modification may negatively impact the performance of your wireless network.

Access Control

The Access Control appoints the authority to wireless client on accessing IEEE 802.11n VAC Access Point, thus a further security
mechanism is provided. This function is available only under AP/Router mode.

Open “Access Control” in “Wireless Settings” as shown next.

«
...
73
74
75
76
77
...
»

Summary of Contents for LWE120A

























































































Reviews:

No comments

Related manuals for LWE120A

Brand: Valcom Pages: 2

Brand: Valcom Pages: 2

Brand: Sage Pages: 84

Brand: Sage Pages: 16

Brand: Avenview Pages: 24

Brand: Häfele Pages: 15

Brand: Bluestone Pages: 11

Brand: SMART-AVI Pages: 2

Brand: DIPRA Pages: 73

Brand: Calphalon Pages: 10

Brand: Gefen Pages: 20

Brand: Oster Pages: 34

STEALTH X2 Series

Brand: SmoothTalker Pages: 4

Brand: Vitek Pages: 42

Brand: KING Pages: 33

Brand: Hamilton Beach Pages: 5

Brand: MS Sedco Pages: 2

Brand: Korenix Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands