Black Box LWE120A User Manual Download Page 3 | Manualshive

Page: 3 / 88

background image

724-746-5500 | blackbox.com

Page 3

FCC and IC RFI Statements/FCC Radiation Exposure Statement

Federal Communications Commission and Industry Canada Radio Frequency Interference

Statements

This equipment generates, uses, and can radiate radio-frequency energy, and if not installed and used properly, that is, in strict
accordance with the manufacturer’s instructions, may cause inter ference to radio communication. It has been tested and found
to comply with the limits for a Class A computing device in accordance with the specifications in Subpart B of Part 15 of FCC
rules, which are designed to provide reasonable protection against such interference when the equipment is operated in a com-
mercial environment. Operation of this equipment in a residential area is likely to cause interference, in which case the user at his
own expense will be required to take whatever measures may be necessary to correct the interference.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.

This digital apparatus does not exceed the Class A limits for radio noise emis sion from digital apparatus set out in the Radio
Interference Regulation of Industry Canada.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques
de la classe A prescrites dans le Règlement sur le brouillage radioélectrique publié par Industrie Canada.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. To avoid the possibility
of exceeding radio frequency exposure limits, you shall beep a distance of at least 100 cm between you and the antenna of the
installed equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

The availability of some specific channels and/or operational frequency bands are country dependent and are firmware
programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user.

«
1
2
3
4
5
...
»

Summary of Contents for LWE120A

























































































Reviews:

No comments

Related manuals for LWE120A

XTENDEX ST-C6USBH-300

Brand: Network Technologies Pages: 15

CAT5 ClassWork Plus Multiloop

Brand: Black Box Pages: 12

Brand: FRAM Pages: 29

Brand: AVARRO Pages: 36

Brand: Gefen Pages: 17

Brand: Concept2 Pages: 69

Brand: Waring Pages: 36

Brand: camry Pages: 40

Brand: Hamilton Beach Pages: 48

NUTRI SMOOTH SPBL-1400B

Brand: Wilfa Pages: 64

Brand: Wilfa Pages: 32

Brand: Panasonic Pages: 24

Brand: Abus Pages: 40

Brand: Jimmy Pages: 80

Brand: Konig Pages: 42

Brand: Gordon Pages: 4

Brand: Grundig Pages: 66

Smart Wi-Fi Extender

Brand: AT&T Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands