Black Box LWE120A User Manual Download Page 14

Page: 14 / 88

724-746-5500 | blackbox.com

Page 14

Chapter 3: Installation

3. Installation

3.1 Preparing for Installation

CAUTION: Professional Installation Required. Seek assistance from a professional installer who is well trained in RF

installation and knowledgeable in the local regulations.

3.2 Safety Precautions

To keep you safe and install the hardware properly, read and follow these safety precautions.

1. If you are installing the Wireless Ethernet Extender for the first time, for your safety as well as others’, please assistance from a

professional installer who has received safety training on the hazards involved.

2. Keep safety as well as performance in mind when selecting your installation site, especially where there are electric power and

phone lines.

3. When installing the Wireless Ethernet Extender, note the following things:

• Do not use a metal ladder;

• Do not work on a wet or windy day;

• Wear shoes with rubber soles and heels, rubber gloves, and a long-sleeved shirt or jacket.

4. When the system is operational, avoid standing directly in front of it. Strong RF fields are present when the transmitter is on.

3.3 Installation Precautions

To keep the Wireless Ethernet Extender well while you are installing it, read and follow these installation precautions.

1. Users MUST use a proper and well-installed grounding and surge arrestor with the Wireless Ethernet Extender; otherwise, ran-

dom lightning could easily cause fatal damage to the unit.

WARNING: EMD (Lightning) DAMAGE IS NOT COVERED UNDER WARRANTY.

2. Users MUST use the power cord and PoE injector shipped in the box with the Wireless Ethernet Extender. Using other options

will damage the unit.

3. Users MUST power off the Wireless Ethernet Extender first before connecting the external antenna to it. Do not switch from

the built-in antenna to the external antenna from Web management without physically installing the external antenna onto the
unit. Otherwise, the Wireless Ethernet Extender might be damaged.

3.4 System Installation
3.4.1 Connect up

1. The bottom of the Wireless Ethernet Extender is a movable cover. Grab the cover and pull it back harder to take it out as the

figure shown below.

Figure 3-1. Removing the bottom cover from the extender.

Summary of Contents for LWE120A

























































































Search results

Summary of Contents for LWE120A

Reviews:

Related manuals for LWE120A

Brands by name

Popular brands

Black Box LWE120A, User Manual

Search results

Summary of Contents for LWE120A

Reviews:

Related manuals for LWE120A

Brands by name

Popular brands