Black Box LWE120A User Manual Download Page 43 | Manualshive

Page: 43 / 88

background image

724-746-5500 | blackbox.com

Page 43

Chapter 5: Navigate the Web Configurator

Figure 5-13. RADIUS Settings.

Authentication RADIUS Server

This is for RADIUS authentication. It can communicate with RADIUS through IP Address, Port, and Shared Secret.

IP Address: Enter the IP address of the Radius Server;

Port: Enter the port number of the Radius Server;

Shared Secret: This secret, which is composed of no more than 31 characters, is shared by the Wireless Ethernet Extender and
RADIUS during authentication.

Global-Key Update

Check this option and specify the time interval between two global-key updates. Default is 3600 seconds.

TCP/IP Settings

When the Router mode is activated, the TCP/IP Settings will show up in Wireless Settings so the user can configure the TCP/IP for
the VAC-managed Access Point.

Figure 5-14. TCP/IP Settings screen.

«
...
41
42
43
44
45
...
»

Summary of Contents for LWE120A

























































































Reviews:

No comments

Related manuals for LWE120A

BEEHIVE OPB6000

Brand: Oster Pages: 12

Brand: Extron electronics Pages: 4

Brand: Wavlink Pages: 2

Brand: Wilson Electronics Pages: 16

DL-DVI-Vision-Fiber-AR-CON

Brand: G&D Pages: 136

EPB-2572 SERIES

Brand: Elite Products Pages: 18

Brand: Skyfood Pages: 20

Brand: Abocom Pages: 2

Brand: Tessa Pages: 56

Brand: Niles Pages: 3

Brand: Camplex Pages: 6

Brand: ARDESTO Pages: 30

Brand: Fluke Pages: 32

Brand: Diablotek Pages: 1

Brand: Wuxi R2TECK Pages: 23

Brand: Biamp Pages: 20

Brand: TP-Link Pages: 65

Brand: EnGenius Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands