Black Box LWE120A User Manual Download Page 83 | Manualshive

Page: 83 / 88

background image

724-746-5500 | blackbox.com

Page 83

Chapter 5: Navigate the Web Configurator

Get Community: Specify the password for the incoming Get and GetNext requests from the management station. By default, it is
set to public and allows all requests.

Set Community: Specify the password for the incoming Set requests from the management station. By default, it is set to private.

Trap Destination: Specify the IP address of the station to send the SNMP traps to.

Trap Community: Specify the password sent with each trap to the manager. By default, it is set to public and allows all requests.

Configure SNMPv3 User Profile

For SNMP protocol version 3, you can click “Configure SNMPv3 User Profile” in blue to set the details of SNMPv3 user. Check
“Enable SNMPv3 Admin/User” in advance and make further configuration.

User Name: Specify a user name for the SNMPv3 administrator or user. Only the SNMP commands carrying this user name are
allowed to access the Wireless Ethernet Extender.

Password: Specify a password for the SNMPv3 administrator or user. Only the SNMP commands carrying this password are
allowed to access the Wireless Ethernet Extender.

Confirm Password: Input that password again to make sure it is your desired one.

Access Type: Select “Read Only” or “Read and Write” accordingly.

Authentication Protocol: Select an authentication algorithm. SHA authentication is stronger than MD5 but is slower.

Privacy Protocol: Specify the encryption method for SNMP communication. None and DES are available. None means no
encryption is applied. DES is a Data Encryption Standard that applies a 58-bit key to each 64-bit block of data.

Certificate Settings

Under Wireless Client mode, when EAP-TLS is used, the RADIUS server must know which user certificates to trust. The Server can
trust all certificates issued by a given CA.

To import a user certificate, from Import User Certificates, click “Browse” and specify the location where the user certificate is
placed. Click “Import.”

Figure 5-75. User Certificates screen.

Delete User Certificate

Delete the selected user certificate.

Import User Certificates

Import the user certificate.

«
...
81
82
83
84
85
...
»

Summary of Contents for LWE120A

























































































Reviews:

No comments

Related manuals for LWE120A

Brand: Bartscher Pages: 16

Brand: Black Box Pages: 2

Brand: C4i Pages: 10

Brand: DVIGear Pages: 10

Brand: Hamilton Beach Pages: 36

EXT-HDMI1.3IR-FO-141

Brand: Gefen Pages: 13

Brand: C-COR.net Pages: 112

Brand: Brandt Pages: 15

Brand: Tru Pages: 12

Brand: XtendLan Pages: 3

EXT-HDMIIR-CAT5

Brand: Gefen Pages: 18

Brand: Hamilton Beach Commercial Pages: 88

Brand: ohmex Pages: 7

Brand: Duronic Pages: 76

Brand: croydon Pages: 2

Fresco RFHE800A

Brand: Razorri Pages: 11

Brand: Avocent Pages: 2

Brand: Vitamix Pages: 160

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands