Black Box LWE120A User Manual Download Page 21

Page: 21 / 88

724-746-5500 | blackbox.com

Page 21

Chapter 4: Quick Setup Tutorial

4. Quick Setup Tutorial

4.1 Access the Web Configurator

The Wireless Ethernet Extender provides you with user-friendly Web-based management interface to easily manage the access
point.

• Configure the computer with a static IP address of 192.168.1.x, as the default IP address of the VAC Access Point is 192.168.1.1.

(X cannot be 0, 1, or 255);

• Open a Web browser and enter the IP address (Default: 192.168.1.1) of the Wireless Ethernet Extender into the address field.

You will see the login page as below.

Figure 4-1. Login page.

• Enter the username (Default: admin) and password (Default: password) respectively and click “Login” to login the main page

of the Wireless Ethernet Extender.

Figure 4-2. Main page.

NOTE: The username and password are case-sensitive, and the password should be no more than 19 characters!

Summary of Contents for LWE120A

























































































Search results

Summary of Contents for LWE120A

Reviews:

Related manuals for LWE120A

Brands by name

Popular brands

Black Box LWE120A, User Manual

Search results

Summary of Contents for LWE120A

Reviews:

Related manuals for LWE120A

Brands by name

Popular brands