Black Box LWE120A User Manual Download Page 29

Page: 29 / 88

724-746-5500 | blackbox.com

Page 29

Chapter 4: Quick Setup Tutorial

4. To decrease the chances of data retransmission at long distances, †he extender can automatically adjust proper ACK timeout

value by specifying the distance between the nodes. Go to WIreless —> Advanced Settings and fill in the
number in the Distance field. If the distance is below 3280 feet (1000 meters), do not change it.

Figure 4-22. Advanced settings screen specifying distance.

4.8.2 Wireless Client Mode

1. Choose Wireless —> Basic Settings. Then you will see the “Wireless Basic Settings” page. Choose “Wireless Client” from

Wireless Mode, and click “Apply” to save it. You can then change the other parameters to optimize your application before
clicking “Apply.”

Figure 4-23. Basic Settings page.

2. Click the “Site Survey” button beside Wireless Mode. It will scan all the

available access points within coverage. Select the one you prefer to connect to, and click “Selected” to establish the connec-
tion.

Summary of Contents for LWE120A

























































































Search results

Summary of Contents for LWE120A

Reviews:

Related manuals for LWE120A

Brands by name

Popular brands

Black Box LWE120A, User Manual

Search results

Summary of Contents for LWE120A

Reviews:

Related manuals for LWE120A

Brands by name

Popular brands