Black Box LWE120A User Manual Download Page 52 | Manualshive

Page: 52 / 88

background image

724-746-5500 | blackbox.com

Page 52

Chapter 5: Navigate the Web Configurator

Figure 5-30. Upgrade Firmware screen.

Upload AC Firmware

Allows the network administrator to upgrade firmware for the Wireless Ethernet Extender in AC mode.

Upload TAP Firmware

Before updating the firmware for the VAC-managed APs, you need to upload the firmware into the VAC Access Point in AC mode
that allows the virtual controller AP to do the firmware upgrade for VAC-managed APs.

CAUTION: Do NOT cut the power off during upgrade; otherwise, the system may crash!

Backup/ Retrieve Settings

We strongly recommend you back up configuration information in case of something unexpected. If tragedy hits your device, you
may have access to restore the important files by the backup. All these can be done by the local or remote computer.

Figure 5-31. Backup configuration screen.

Save AC Settings to File

Click Save to export the configuration file of the Wireless Ethernet Extender in AC mode. Then the configuration file ac.cfg will be
generated and saved to the specified location.

Save TAP Settings to File

Click Save to export the configuration file of the Wireless Ethernet Extender. Then the configuration file tap.cfg will be generated
and saved to the specified location.

«
...
50
51
52
53
54
...
»

Summary of Contents for LWE120A

























































































Reviews:

No comments

Related manuals for LWE120A

Brand: Oster Pages: 24

Brand: Value Pages: 4

Brand: Lindy Pages: 36

Brand: Macab Pages: 8

Brand: Gefen Pages: 20

La Rochelle MIX 370

Brand: Gallet Pages: 36

Brand: Black Box Pages: 30

Brand: Vitek Pages: 40

Brand: Toya Pages: 48

AVX-HDMI2-HDB-KIT

Brand: Black Box Pages: 24

Brand: Ihse Pages: 64

Brand: DS Produkte Pages: 28

Brand: Reely Pages: 4

Brand: Fagor Pages: 40

Brand: Zelmer Pages: 30

Brand: Zelmer Pages: 46

Brand: zBoost Pages: 12

Brand: Kushi Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands