Black Box LWE120A User Manual Download Page 53 | Manualshive

Page: 53 / 88

background image

724-746-5500 | blackbox.com

Page 53

Chapter 5: Navigate the Web Configurator

Load Settings from File

Import ac.cfg load into the VAC Access Point in AC mode.

Restore Factory Default Settings

The IEEE 802.11n VAC Access Point provides two ways to restore the factory default settings:

Restore factory default settings via Web

From Configuration File in Management, click Reset restore factory default settings.

Figure 5-32. Configuration file screen.

Restore factory default settings via Reset Button

If software in the Wireless Ethernet Extender unexpectedly crashes and you can no longer reset the unit via Web, you may do a
hardware reset via the reset button. Press and hold the button for at least 5 seconds and then release it until the PWR LED blinks.
The hardware reset will take about 2 minutes to complete.

Reboot

You can software reboot your Wireless Ethernet Extender from Configuration File in Management as described next:

Figure 5-33. Rebooting from the Configuration screen.

Click “Reboot” and c lick “Yes” when prompt appears to start reboot process. This takes a few minutes.

«
...
51
52
53
54
55
...
»

Summary of Contents for LWE120A

























































































Reviews:

No comments

Related manuals for LWE120A

Brand: Oster Pages: 6

Activmix Premium 2103

Brand: eta Pages: 48

Brand: Jata electro Pages: 20

Brand: Russell Hobbs Pages: 16

Brand: Sensei Pages: 27

Brand: Solutions Pages: 10

Brand: Kalorik Pages: 24

Brand: Celabs Pages: 2

Brand: Narita Pages: 14

Brand: Blendtec Pages: 16

Brand: camry Pages: 40

Brand: Fagor Pages: 40

Brand: RS Pages: 3

Brand: Edimax Pages: 11

Brand: Edimax Pages: 58

Brand: Black Box Pages: 13

Brand: Black Box Pages: 16

Brand: Black Box Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands