Black Box LWE120A User Manual Download Page 77 | Manualshive

Page: 77 / 88

background image

724-746-5500 | blackbox.com

Page 77

Chapter 5: Navigate the Web Configurator

Traffic Shaping

This allows the administrator to manage the traffic flow to ensure optimal performance.

Figure 5-66. Traffic Shaping screen.

Overall Traffic Shaping

Check this box to control the overall bandwidth of the Wireless Ethernet Extender.

Incoming Traffic Limit: To specify the maximum incoming bandwidth to a certain rate in kbps.

Incoming Traffic Burst: To specify the buffer size for incoming traffic that can be sent within a given unit of time. The suggested
value is 20 KBytes. You may just leave the default value there, and then the connection will be bound to the traffic shaping rule at
all times. You may decrease it to smaller value if the incoming traffic limit is smaller.

Outgoing Traffic Limit: To limit the outbound traffic to a certain rate in kbit/s.

Outgoing Traffic Burst: To specify the buffer size for outbound traffic. The suggested value is 20KBytes. You may decrease it to
smaller value if the outbound traffic limit is smaller.

VAP Traffic Shaping

Check this box to control the overall bandwidth for a specific VAP network.

Incoming Traffic Limit: To specify maximum incoming bandwidth to a certain rate in kbps.

Incoming Traffic Burst: To specify the buffer size for incoming traffic that can be sent within a given unit of time. The suggested
value is 20 KBytes. You may just leave the default value there, and then the connection will be bound to the traffic shaping rule at
all times. You may decrease it to smaller value if the incoming traffic limit is smaller.

Captive Portal

Captive portal is management that allows WLAN users to easily and securely access the Internet. Under Router mode, when
captive portal is enabled, the Wireless Ethernet Extender will redirect the client to go to an authentication web page before
browsing Internet web pages. Captive portals are used on most Wi-Fi hotspots networks. Therefore, to use captive portal, you
need to find the service providers that have the additional services needed to make captive portal work.

«
...
75
76
77
78
79
...
»

Summary of Contents for LWE120A

























































































Reviews:

No comments

Related manuals for LWE120A

DSM-750 - MediaLounge High-Definition Draft N Media...

Brand: D-Link Pages: 138

Brand: Intelix Pages: 2

715 LOOP EXPANDER

Brand: DMP Electronics Pages: 2

SLI ENFORCER MVD-V1201-1Q

Brand: SECO-LARM Pages: 4

Brand: Happy Baby Pages: 9

Brand: Post Pages: 13

Brand: Tower Hobbies Pages: 16

Brand: KanexPro Pages: 4

Space-Saving Blender

Brand: Hamilton Beach Pages: 24

Brand: Blackbird Pages: 14

Brand: Link Pages: 23

Brand: Currys Essentials Pages: 2

VITALIZER TCM 401

Brand: Tecnora Pages: 8

RE270K / RE370K

Brand: TP-Link Pages: 34

Brand: Asus Pages: 119

Brand: CLEAN ROOM DEVICES Pages: 22

Brand: Hamilton Beach Commercial Pages: 88

COPPERLINK 2151

Brand: Patton electronics Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands