Black Box Compact T1 MT850A User Manual Download

Page: 304 / 592

5-220

Compact T1 - Release 6.1

CLI Commands

show

show (router) dhcp

The show (router) dhcp command displays the current DHCP settings for the Router card.

Syntax:

show {rtr_card-addr} dhcp

Example:

show 5 dhcp

The example shows the DHCP settings for the Router card in slot 5.

> show 5 dhcp

SLOT 5:

DHCP Server/BOOTP Relay Agent Settings for Router:

DHCP: Disabled

{rtr_card-addr}

The slot number (1-6) that contains the Router (IP or CMG) card.

show (router) dns

The show (router) dns command displays the current DNS setup for the Router card.

Syntax:

show {rtr_card-addr} dns

Example:

show 3 dns

> show 5 dns

SLOT 5:

DNS Settings:

DNS Resolver: Disabled

DNS Server 1 IP Address: 0.0.0.0

DNS Server 2 IP Address: 0.0.0.0

DNS Host Name:

DNS Default Domain:

DNS Static Host List:

Total: 0

{rtr_card-addr}

The slot number (1-6) that contains the Router card.

Summary of Contents for Compact T1 MT850A
















































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Compact T1 MT850A

Reviews:

Related manuals for Compact T1 MT850A

Brands by name

Popular brands

Black Box Compact T1 MT850A, User Manual

Search results

Summary of Contents for Compact T1 MT850A

Reviews:

Related manuals for Compact T1 MT850A

Brands by name

Popular brands