manualshive.com logo in svg

Black Box Compact T1 MT850A, User Manual

Looking for a user manual for the Black Box Compact T1 MT850A? Look no further! Download your free manual from manualshive.com and make the most out of this exceptional product. Gain valuable insights and unleash the full potential of your Black Box Compact T1 MT850A with our comprehensive user manual.

Share
Download
background image

8-2

Compact T1 - Release 6.1

FXS Voice Card

Overview

Overview

The FXS Voice Service card provides high-density provisioning of cost-effective 
telephone services. Eight Foreign Exchange Station (FXS) telephone line channels can 
be deployed on each FXS Voice Service card. These cards can be inserted into any card 
slot of the six-slot Compact T1. This allows the provisioning of up to 48 FXS lines in 
a single chassis and up to 96 lines in two side-by-side units occupying just two rack 
units of space.

A unique range of software-controlled signaling capabilities connects virtually any 
type of 2-wire battery-feed telephone line service. FXS loop start or ground start 
interfaces provide either outside (external) phone lines or on-premises (internal) 
business line services. Supported features include caller ID, calling party disconnect, 
distinctive ringing, three-way calling, and E&M signaling conversion. Automatic 
impedance balancing provides echo-free service connections for a wide range of 
customer equipment and line conditions. V.90 transmission ensures optimal dial-up 
modern performance.

As a component of the Compact T1 platform, the FXS service card has several local 
and remote management options available through the Controller. The card can be 
locally configured and managed using the front-panel DIP switches or the Command 
Line Interface (CLI). Front-panel LEDs quickly communicate call progress and 
channel status. 

Summary of Contents for Compact T1 MT850A

















































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Compact T1 MT850A

iDiPOS MS3390 User Manual preview
MS3390
Brand: iDiPOS Pages: 93
Ingenico i8550 Specifications preview
i8550
Brand: Ingenico Pages: 2
adstec VMT6008 User Manual preview
VMT6008
Brand: adstec Pages: 46
Honeywell CT40 HomeBase Quick Start Manual preview
CT40 HomeBase
Brand: Honeywell Pages: 8
Honeywell SP5600-C OptimusR User Manual preview
SP5600-C OptimusR
Brand: Honeywell Pages: 15
Honeywell TemaLine TemaKey Installation Manual preview
TemaLine TemaKey
Brand: Honeywell Pages: 32
Honeywell temaserver TS TA series Installation Manual preview
temaserver TS TA series
Brand: Honeywell Pages: 23
Honeywell TemaKey Installation Manual preview
TemaKey
Brand: Honeywell Pages: 30
Honeywell TemaKey TK C03 Installation Manual preview
TemaKey TK C03
Brand: Honeywell Pages: 21
Philips MAT960 Owner'S Manual preview
MAT960
Brand: Philips Pages: 40
Philips MAT972 Owner'S Manual preview
MAT972
Brand: Philips Pages: 44
ELCOM W-615 User Manual preview
W-615
Brand: ELCOM Pages: 32
Element CA850 User Manual preview
CA850
Brand: Element Pages: 28
Element 455W User Manual preview
455W
Brand: Element Pages: 34
Omron NXR Series User Manual preview
NXR Series
Brand: Omron Pages: 134
HYOSUNG MoniMax7600I Installation Manual preview
MoniMax7600I
Brand: HYOSUNG Pages: 30
Vivotech ViVOpay 5000 User Manual preview
ViVOpay 5000
Brand: Vivotech Pages: 14
Doosan LIN-Q DTM-01 User Manual preview
LIN-Q DTM-01
Brand: Doosan Pages: 30

Brands by name

Popular brands

Load more brands