Black Box Compact T1 MT850A User Manual Download

Page: 369 / 592

Compact T1 - Release 6.1

5-285

CLI Commands

telnet

telnet

telnet (router)

Use the telnet (router) command to establish a Telnet session from the Compact T1 CLI to the
Router card menu-driven user interface.

Syntax:

telnet {rtr-addr}

Example:

telnet 1

The example will Telnet into a Router in Slot 1.

> telnet 3

Connected.

Escape character is ’^]’.

Attempting Router connection...

Router [Wed Apr 24, 2002 13:00:15] (<CR> to login)

Password >******

Select a terminal type...

(<space> or <back-space> to toggle, <CR> to accept)

Terminal: <VT100>

{rtr-addr}

The Router address is in the form {slot|slot:port}.

slot

Slot location (1 - 6) of a Router (IP or CMG) card.

port

Port number of a Router is 1. Note: only required on IP Router when
release 1.1 or earlier.

Summary of Contents for Compact T1 MT850A
















































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Compact T1 MT850A

Reviews:

Related manuals for Compact T1 MT850A

Brands by name

Popular brands

Black Box Compact T1 MT850A, User Manual

Search results

Summary of Contents for Compact T1 MT850A

Reviews:

Related manuals for Compact T1 MT850A

Brands by name

Popular brands