manualshive.com logo in svg

Black Box Compact T1 MT850A, User Manual

Looking for a user manual for the Black Box Compact T1 MT850A? Look no further! Download your free manual from manualshive.com and make the most out of this exceptional product. Gain valuable insights and unleash the full potential of your Black Box Compact T1 MT850A with our comprehensive user manual.

Share
Download
background image

15-8

Compact T1 - Release 6.1

V.35/V.54 Cards

Cables

Cables

Depending on your application, you will need to purchase one or more of the available  
V.35 data cables:

These cables can be purchased at a licensed distributor.

Part Number

Description

Notes

005-0014

V.35 Female 
10-foot cable

These cables are used to provide the V.35 DCE 
interface on a male connector to typical DTE 
applications. Order one cable per V.35 port. 

005-0068

V.35 Female 
25-foot cable

005-0069

V.35 Female 
50-foot cable

005-0010

V.35 Male 
50-foot cable

V.35 data cables with male connector for 
connecting a router with a female V.35 
Winchester connector or other data equipment to 
a Compact T1 V.35 data port (sub-miniature DB-
26). Order one cable per V.35 port. 

005-0009

V.35 Male 
25-foot cable

005-0008

V.35 Male 
10-foot cable

005-0189

DB-25 V.35 Female 
50-foot cable

These cables are used to provide a DB-25 DCE 
V.35 female interface for connection to a male 
DB-25 DTE V.35 interface. Order one per port.

005-0188

DB-25 V.35 Female 
25-foot cable

005-0187

DB-25 V.35 Female 
10-foot cable

005-0186

DB-25 V.35 Female 
6-foot cable

Summary of Contents for Compact T1 MT850A

















































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Compact T1 MT850A

TableSafe RAIL User Manual preview
RAIL
Brand: TableSafe Pages: 23
EBN Technology TM-70 Service Manual preview
TM-70
Brand: EBN Technology Pages: 19
Worth Data 701 RF User Manual preview
701 RF
Brand: Worth Data Pages: 155
ahlsell ENERGY FLEX SKP 20 User Manual preview
ENERGY FLEX SKP 20
Brand: ahlsell Pages: 16
ABB REL 505-C1 2.3 Series Installation And Commissioning Manual preview
REL 505-C1 2.3 Series
Brand: ABB Pages: 118
PAR EverServ 600 User Manual preview
EverServ 600
Brand: PAR Pages: 11
Datecs BluePad-55 v2 User Manual preview
BluePad-55 v2
Brand: Datecs Pages: 23
barclaycard takepayments A920 Installation And User Manual preview
takepayments A920
Brand: barclaycard Pages: 25
EC Line EC-1519I3 User Manual preview
EC-1519I3
Brand: EC Line Pages: 13
Partner E5-1-K Service Manual preview
E5-1-K
Brand: Partner Pages: 64
ZKTeco U1000F Installation Manual preview
U1000F
Brand: ZKTeco Pages: 11
NEO TSST Kiosk Quick Start Manual preview
TSST Kiosk
Brand: NEO Pages: 6
Omnicomm OKO 3.0 Assembly Instructions Manual preview
OKO 3.0
Brand: Omnicomm Pages: 56
EchoStar inmarsat Hughes 9450 Series Installation Manual preview
inmarsat Hughes 9450 Series
Brand: EchoStar Pages: 25
Data General Dasher D411 User Manual preview
Dasher D411
Brand: Data General Pages: 124
TSYS Ingenico Desk 3500 Quick Reference Manual preview
Ingenico Desk 3500
Brand: TSYS Pages: 2
Partner C14-1R Quick Start Manual preview
C14-1R
Brand: Partner Pages: 2
SAND PS400 EFT-POS Manual preview
PS400 EFT-POS
Brand: SAND Pages: 6

Brands by name

Popular brands

Load more brands