Black Box Compact T1 MT850A User Manual Download | Manualshive

Page: 316 / 592

background image

5-232

Compact T1 - Release 6.1

CLI Commands

show

Static IPX Network Settings for LocalAdit:

Total: 0

Static IP Address Settings for LocalAdit:

Total: 0

Static MAC Address Settings for LocalAdit:

Total: 0

LAN Filters Enabled for LocalAdit:

Forward Mode: Forward ALL Frames NOT Matching Filters

Filter Type Source/Dest Filter Name

----------- ----------- -----------

Total: 0

LAN MAC Address Filters Defined for LocalAdit:

Total: 0

LAN Protocol Filters Defined for LocalAdit:

Total: 0

LAN Custom Filters Enabled Defined for LocalAdit:

Total: 0

{rtr-addr}

The Router (IP or CMG) address is in the form {slot:port} or {slot "profile-name"}.

slot

The slot number (1-6) that contains the Router card.

port

Port number of the Router is 1.

"profile-name"

The profile name for the Router interface that is used to reach this
destination. Name must be enclosed in quotes, with a maximum
length of 11 characters.

«
...
314
315
316
317
318
...
»

Summary of Contents for Compact T1 MT850A

















































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Compact T1 MT850A

Brand: Allen-Bradley Pages: 4

Morpho RapID 1 G Series

Brand: Sagem Securite Pages: 13

Brand: Quest Payment Systems Pages: 37

VERIFONE OMNI Series

Brand: Harbortouch Pages: 2

Brand: National Instruments Pages: 14

Brand: National Instruments Pages: 30

Brand: Invenco Pages: 40

Brand: IDTECH Pages: 523

Brand: Uni-Ubi Pages: 7

Brand: Bluebird Pages: 24

Brand: Bluebird Pages: 31

Brand: Pundi X Pages: 19

Brand: YASKAWA Pages: 48

Ingenico IWL250

Brand: Tailwind Pages: 2

Ingenico IPP320 PEDPack

Brand: Tailwind Pages: 2

POS-8017F Series

Brand: Fametech Pages: 113

Brand: POSline Pages: 69

SBXMDS040 MDT20

Brand: Xerox Pages: 31

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands