Black Box Compact T1 MT850A User Manual Download

Page: 488 / 592

14-14

Compact T1 - Release 6.1

Router (CMG) Card

Card Configuration

set (router-trunk) voice bandwidth limit
Set percentage of bandwidth on the trunk that is reserved for routed or
bridged data

set (router-voice) algorithm preference
Specify the list of voice coding algorithms to be supported for VoIP calls

set (router-voice) cpd
Configure how calling party disconnect should be signaled to an endpoint

set (router-voice) default
Specify the list of voice coding algorithms to be supported for VoIP calls

set (router-voice) dtmfrelay
Specify the encapsulation to use on the Router interface

set (router-voice) echo cancellation
Enable/disable echo cancellation

set (router-voice) echo tail
Set the maximum time between the signal and its echo

set (router-voice) endpoint prefix
Set the prefix and suffix of the MGCP endpoint names

set (router-voice) log start
To start logging events to the CMG text log

set (router-voice) log stop
To stop logging events to the CMG text log

set (router-voice) rxgain
Set gain on receive side for voice channel

set (router-voice) silence
Enable/disable silence suppression

set (router-voice) slash
Suppresses the implied slash "/" between the endpoint prefix and suffix

set (router-voice) tos
Set gain on transmit side for voice channel

set (router-voice) txgain
Set the gain on the transmit side (TDM-to-packet) voice path

set (router-voice) up
Set the specified voice channel up or down

Summary of Contents for Compact T1 MT850A
















































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Compact T1 MT850A

Reviews:

Related manuals for Compact T1 MT850A

Brands by name

Popular brands

Black Box Compact T1 MT850A, User Manual

Search results

Summary of Contents for Compact T1 MT850A

Reviews:

Related manuals for Compact T1 MT850A

Brands by name

Popular brands