Black Box Compact T1 MT850A User Manual Download

Page: 409 / 592

Compact T1 - Release 6.1

9-5

ISDN BRI Card

Technical Specifications

Network Standards

Telcordia TR-NWT-000397 (1993)

Telcordia TR-TSY-000821 (1991)

Telcordia TR-TSY-000829 (1989)

ANSI T1.1992

ITU-T Q.920, Q.921

Clocking

Loop timing derived from Channel 1 of ISDN BRI card or any Compact T1 T1
line

Testing & Diagnostics

Initiates 2B+D, B1, or B2 loopbacks toward the BRI at the NT1

Performs self test at power up

3 DSO mode: supports external loopback testing via EOC messages from the
switch

Product Supports

TR-821 alarms

TR-397/TR-829/TR-821 Generic Segmented Performance Monitoring

TR-829 multi-EOC messages in 3 DS0 and 4:1 TDM modes

Metallic DC test signature in Line Unit Network Terminal (LUNT) mode

Power

Maximum power input: 6 W (8 port)

Solid-state fuseless protection

Summary of Contents for Compact T1 MT850A
















































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Compact T1 MT850A

Reviews:

Related manuals for Compact T1 MT850A

Brands by name

Popular brands

Black Box Compact T1 MT850A, User Manual

Search results

Summary of Contents for Compact T1 MT850A

Reviews:

Related manuals for Compact T1 MT850A

Brands by name

Popular brands