Black Box Compact T1 MT850A User Manual Download

Page: 456 / 592

12-12

Compact T1 - Release 6.1

Quad T1 Card

Configuration Restrictions

Configuration Restrictions

There are some configuration restrictions with the Quad T1 Service Card.

If an Compact T1 contains three (3) Quad T1 cards:

remaining three (3) slots can be any combination of BRI, FXS, FXO or Router
cards.

remaining three (3) slots can contain two (2) V.35 cards, with the remaining slot
empty.

If an Compact T1 contains four (4) Quad T1 cards:

remaining two (2) slots must be empty.

Summary of Contents for Compact T1 MT850A
















































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Compact T1 MT850A

Reviews:

Related manuals for Compact T1 MT850A

Brands by name

Popular brands

Black Box Compact T1 MT850A, User Manual

Search results

Summary of Contents for Compact T1 MT850A

Reviews:

Related manuals for Compact T1 MT850A

Brands by name

Popular brands