manualshive.com logo in svg

Black Box Compact T1 MT850A, User Manual

Looking for a user manual for the Black Box Compact T1 MT850A? Look no further! Download your free manual from manualshive.com and make the most out of this exceptional product. Gain valuable insights and unleash the full potential of your Black Box Compact T1 MT850A with our comprehensive user manual.

Share
Download
background image

5-168

Compact T1 - Release 6.1

CLI Commands

set

set (router-trunk) voice bandwidth limit

Use the set (router-trunk) voice bandwidth limit command to specify the maximum 
percentage of bandwidth on this trunk that voice calls are allowed to consume. The remaining 
percentage of the bandwidth on a CMG trunk to be reserved for routed or bridged data. Routed 
or bridged data is allowed to use any available bandwidth, but it is carried at a lower priority 
than the voice. If the bandwidth required to carry an additional VoIP call will put the total 
bandwidth used by VoIP calls above that allowed for voice on the trunk, then the call will be 
denied and the caller will hear the all-circuits-busy tone. This command applies to the CMG 
Router card only.

Syntax:

set {cmg-trunk-addr} voice bandwidth limit {percent}

Example:

set 2:1:1 voice bandwidth limit 90

The example will limit voice calls to 90% of the bandwidth on trunk 1 of the 
CMG card in slot 2.

{cmg-trunk-addr}

{percent}

The maximum percentage of VoIP bandwidth. Range is 0 - 100.

slot

The slot number (1-6) that contains the CMG card.

port

Port number of the Router is 1.

trunk

Trunk number for this port, 1-24.

Summary of Contents for Compact T1 MT850A

















































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Compact T1 MT850A

NCR RealPOS 5977 User Manual preview
RealPOS 5977
Brand: NCR Pages: 172
Bitron Video AV0151/010 Instruction Manual preview
AV0151/010
Brand: Bitron Video Pages: 7
National Instruments TBX-96 Manual preview
TBX-96
Brand: National Instruments Pages: 12
National Instruments TB-2605 Installation Manual preview
TB-2605
Brand: National Instruments Pages: 12
Wincor Nixdorf BEETLE/S User Manual preview
BEETLE/S
Brand: Wincor Nixdorf Pages: 43
Wincor Nixdorf BEETLE /XL User Manual preview
BEETLE /XL
Brand: Wincor Nixdorf Pages: 97
Janus POTSwap EVDO910PS User Manual preview
POTSwap EVDO910PS
Brand: Janus Pages: 20
ZyXEL Communications OLT-1308 User Manual preview
OLT-1308
Brand: ZyXEL Communications Pages: 314
POSIFLEX KS-6810 SERIES Technical Manual preview
KS-6810 SERIES
Brand: POSIFLEX Pages: 50
UTC RETAIL 2250 User Manual preview
2250
Brand: UTC RETAIL Pages: 12
UTC RETAIL 3100 Series User Manual preview
3100 Series
Brand: UTC RETAIL Pages: 16
Ingenico group Move 3500 WiFi Quick Start Manual preview
Move 3500 WiFi
Brand: Ingenico group Pages: 2
Zenith ZTX-10 Series User Manual preview
ZTX-10 Series
Brand: Zenith Pages: 60
Landi E830 User Manual preview
E830
Brand: Landi Pages: 18
ZETRON 640 DAPT XTRA Installation And Repair Manual preview
640 DAPT XTRA
Brand: ZETRON Pages: 210
Vector Graphic Mainframe User Manual preview
Mainframe
Brand: Vector Graphic Pages: 14
HappyOrNot Smiley Touch HONT1000 Assembly Manual preview
Smiley Touch HONT1000
Brand: HappyOrNot Pages: 12
EC Line EC-VP-1100 Instructions For Assembly/Disassembly preview
EC-VP-1100
Brand: EC Line Pages: 7

Brands by name

Popular brands

Load more brands